background image

23

ENGLISH

Functions during the dive

4.3.2  Preparation for the dive and function check

Switch on Aladin TEC 3H by pushing 

 and check the test display: Are 

all elements of the display activated? Do not use Aladin TEC 3H if the display 
does not show all elements. When switching on Aladin TEC 3H with 

the test display will not appear.

 WARNING

Check the battery capacity before each dive ->15.

4.4 Functions during the dive

4.4.1  Immersion

If the water contacts are deactivated (->70), switch on Aladin TEC 3H before immersion.

 WARNING

If you have chosen the option "Water contacts off" ("set 1" or LogTRAK), Aladin TEC 3H will turn on 
with a delay of up to 1 minute into the dive. This will affect functioning of the computer. Make sure 
that the computer is on before starting the dive. 

After immersion, starting at a depth of about 0.8m (3ft), all diving functions are monitored, i.e. depth, 
tank pressure and dive time displayed, maximum depth stored, saturation of tissues calculated, 
no-stop time or decompression prognosis determined, ascent rate controlled and displayed and the 
correctness of the decompression procedure supervised.

4.4.2  Setting bookmarks

During the dive you can create bookmarks in your dive profile by pressing 

 . The logbook icon 

 

appears for 4 seconds and an audible signal confirms the creation of the bookmark. These bookmarks 
will be graphically displayed in the dive profile of LogTRAK.

4.4.3  Dive time 

The whole time spent below a depth of 0.8m (3ft) is displayed as dive time 
in minutes. The time above 0.8m (3ft) is counted as dive time only if the diver 
descends again below 0.8m (3ft) within 5 minutes.

While the dive time is running, the colons on the right of the figures are flashing 
in one second intervals. Maximum dive time displayed is 199 minutes.

 WARNING

Half time alarm (turn around alarm)
If half of the set maximum dive time has elapsed, an audible signal goes off and

flashes for 1 minute.

 WARNING

Set dive time has elapsed ->69
An audible signal goes off and the dive time starts flashing.

Dive time

Summary of Contents for Aladin TEC 3H
















































































Reviews: