manualshive.com logo in svg

Uvitron Intelliray 600, Instruction Manual

Share
Download
Uvitron Intelliray 600 Instruction Manual Download Page 15

Uvitron International INTELLI-RAY 600 Instruction Manual, Rev. T 

Page 15 of 36 

 

SYSTEM OPERATION  (CONTINUED) 

6 

 

Fig. 5B, IntelliRay Setup Menu Map:

 This diagram and the one on the following page show the 

display  screens  of  the  IntelliRay  Setup  menus,  and  the  key  presses  (in  uppercase)  used  to 
sequence through them. Refer to fig. 5A on the previous page for the Main Menu Map. 

ENTR 

KEY: 

BLUE 

= Key Press, 

           = Menu Item # 

 

XX 

ENTR 

MENU 

Enter Password 

  (0 – 9999): **** 

Setup Menu 

COM Port Unit ID 

(0 - 7): 1 

S1* 

S2 

S3 

S4 

S5 

S7 

MENU 

MENU 

MENU 

MENU 

ENTR 

ENTR 

COM Port = RS232 

ENTR to Toggle 

COM Port = RS485 

ENTR to Toggle 

Key/Cyc Beep ON 

ENTR to Toggle 

Key/Cyc Beep OFF 

ENTR to Toggle 

Backlight ON 

ENTR to Toggle 

Backlight OFF 

ENTR to Toggle 

ENTR 

ENTR 

MENU 

MENU 

MENU 

Interlock ON 

ENTR to Toggle 

Interlock OFF 

ENTR to Toggle 

MENU 

MENU 

*Note: This password entry menu item 
will only be displayed if a password has 
been previously entered (see S1 and 
S13 of section 6.6). 

 

From Setup Menu 

Exit item S14 on 

page 16 

To Setup Menu 

Temp Unit menu 

item S8 on page 16 

Main menu 

Setup Entry 

item M3 

on page 14 

 

S6 

MENU 

Alarm Beep ON 

ENTR to Toggle 

Alarm Beep OFF 

ENTR to Toggle 

ENTR 

MENU 

Summary of Contents for Intelliray 600





































Reviews:

No comments

Brands by name

Popular brands

Load more brands