manualshive.com logo in svg

Uvitron Intelliray 600, Instruction Manual

Share
Download
Uvitron Intelliray 600 Instruction Manual Download Page 11

Uvitron International INTELLI-RAY 600 Instruction Manual, Rev. T 

Page 11 of 36 

 

CONTROLS AND INDICATORS  (CONTINUED) 

5 

 

Item 

Description 

1.  Handle 

The  IntelliRay  handle  can  be  used  to  carry  the  lamp  housing 
assembly, or to raise or lower the unit height. 

WARNING:

  The handle should never be used to lift or carry the 

IntelliRay when mounted to a stand or other supporting device. 

2.  Backlit LCD Display 

The  LCD  display  is  used  to  convey  messages  to  the  operator. 
The display backlight can be turned on or off in the Setup menu. 

3.  LED Status Indicators 

The 4 front panel LEDs display the following system status info: 
1. READY: Lights when the lamp completes its power-on warm-
up  cycle  and  reaches  stable  output  intensity.  The  Ready  LED 
also flashes when the shutter is opened. 
2.  STANDBY:  Lights  when  shutter  is  closed  and  output  is 
reduced to low power, flashes when door/ext. interlock is active. 
3. SHUTTER: Lights when shutter is opened. 
4. ALARM: Lights when abnormal system condition detected. 

4.  Control Keypad 

Keypad buttons are used to enter all system parameters and to 
navigate through system menus. 

5.  Lamp Access Panel 

The  Lamp  Access  Panel  can  be  removed  for  inspection  or 
replacement of the arc lamp.  

WARNING:

    High  voltages  and  high  temperatures  are 

accessible  with  this  panel  removed.  Always  switch  the  Input 
Power Switch off, disconnect the input power cord, and wait for 
the unit to cool before removing this panel. 

6.  External Interface 
Connector 

RS232/RS485  and  logic  control  signal  D-SUB  connector. 
Optional or customer equipment may be interfaced here. 

7.  Input Power Switch & 
Receptacle 

The Input Power switch is used to apply or remove main power 
to  the  IntelliRay  system.  Co-located  with  the  switch  is  the 
universal IEC power cord receptacle. 

8.  Cooling Fan w/ 
removable filter 

The  system  cooling  fan  has  a  foam  filter  element  that  can  be 
removed for periodic cleaning (as required). 

9.  Height Adjustment Knob 

When  used  with  the  optional  Flood  Stand,  the  rear  mounted 
Height  Adjustment  Knob  is  used  to  set  the  optimum  distance 
from the lamp to the substrate being cured. 

Summary of Contents for Intelliray 600





































Reviews:

No comments

Brands by name

Popular brands

Load more brands