background image

28

1000033244-00

4. Instructions for use

7. Warranty and Repair

7-1. Warranty

This measuring instrument is delivered after USHIO has thoroughly inspected the
instrument and check that its performance satisfies the specifications. If this instru-
ment fails due to its material or poor workmanship, or if it has failed due to an acci-
dent during transportation, please contact USHIO. The warranty term of this instru-
ment shall be one year after its delivery or three months after repair. If this instrument
fails under normal operating conditions within this warranty term, USHIO will repair
or replace the instrument free of charge.
However, this instrument is not covered by warranty I fit is used in a wrong manner (a
manner not described in the operation manual) or in the careless manner, if it is modi-
fied, or if it has failed due to a natural disaster, etc.

7-2. Repair

If this instrument is judged as to have failed, or if you are unclear on any point, please
inform USHIO of the model manufacturing number and symptom in details. How-
ever, please understand that USHIO is not obligated to repair the instrument if it is
modified.

7-3. Calibration (Main Unit and Photodetector Unit)

In order to ensure measurement accuracy, it is recommended that this instrument be
calibrated once every 6 months.
If you have any questions concerning repair or calibration please contact your repre-
sentative salesperson.

7. W

arranty and Repair

Summary of Contents for UIT-250









































Reviews: