manualshive.com logo in svg

US Cutter LaserPoint, User Manual

Share
Download
US Cutter LaserPoint User Manual Download Page 10

- 9 - 

 

Pressure Setting Mode 

 The Pressure Setting Mode is used to adjust the pressure of the cutting blade. 
Thicker materials can require more pressure. The pressure should be strong 
enough to fully cut the top vinyl but not strong enough to cut through the 
backing attached to your vinyl. If you are unsure of the cutting pressure that you 
should use, it is advised to make a test cut. This can be done by holding the Test 
Button in this mode or by returning to Jog Mode and pressing the Test Button. 
You can see how the pressure effects the down cutting position of the blade by 
returning to Jog Mode and using the Up/Down Buttons.

 

Test Button

 

Returns the cutter to Jog Mode 

(If held down, a test cut 

will be made).

 

On Line Button

 

(has no function in this mode).

 

Mode Button

 

Cycles through the 7 Off Line modes.

 

Pause Button 

 

Returns the cutter to Jog Mode.

 

Directional Buttons

 

(has no function in this mode). 

Target Button

 

(has no function in this mode). 

Up/Down Buttons

 

(has no function in this mode).

 

Plus/Minus Buttons

 

Increases/Decreases the amount of pressure used 
when cutting (

ranges from 0 to 200

). Thicker materials 

may require more pressure. The amount of pressure 
used can be seen by going to the Jog Mode and using 
the Up/Down buttons to switch the blade from the 
original position to the Down cutting position. 
 
 

  

 

 

 

 

 

 

Summary of Contents for LaserPoint


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands