manualshive.com logo in svg

US Cutter Copam, User Manual

Share
Download
US Cutter Copam User Manual Download Page 14

- 13 - 

 

If you are using a Serial or Parallel Cable to connect your cutter to a computer then no further setup is 
necessary. Simply connect one end of the cable to the cutter and the other end to a computer and setup is 
complete. 

If you have more than one serial/parallel connection on your computer or you are experiencing 

communication issues between your cutter and computer then you may wish to verify that the correct port is being used 
in your software setup (see Finding Your COM/LPT Port on the next page), but for most users the port will be 1(i.e. 
COM1/LPT1).

  

If Using the USB Cable to connect your cutter to a Computer: 

You will need to install drivers for the USB connection to work properly. These drivers can either be 
obtained from the supplied drivers disc or downloaded from the support website (

in the

 

downloads section of 

support.uscutter.com

).

Mac Users will need to download drivers from the support website as the drivers included on the 

disc are Windows only.  

Windows XP Users: 

1.

 

Insert the driver disc or download (and unzip if necessary) drivers to your system.  

2.

 

Connect the USB Cable to your computer and your cutter. The Found New Hardware wizard will 
appear. 

3.

 

When asked, “Can Windows connect to Windows Update to search for software?” select “No, not 
this time” and click next. 

4.

 

When asked, “What do you want the wizard to do?” select “Install from a list or specific location 
(Advanced)” and click next. 

5.

 

Choose the “Search for the best driver in these locations” radio button and check the “Include this 
location in the search” checkbox. Now type  (

or browse to find

) the location of the downloaded 

drivers/inserted drivers disc and click next.  

6.

 

 When the wizard is complete, click the Finish button. 

7.

 

The Found New Hardware wizard should appear again. When it does, follow steps 3-6 again for 
the second driver.  

Windows Vista Users: 

If you want to use downloaded drivers, download them before starting the install process. 

1.

 

Connect the USB Cable to your computer and your cutter. The Found New Hardware wizard will 
appear. 

2.

 

When told that “Windows needs to install driver software…” select “Locate and install driver 
software (recommended)”. 

3.

 

If Windows finds and downloads your needed drivers then the process is complete. Repeat the 
previous steps again for the second needed driver. If Windows does not find and download the 
needed drivers proceed to the next step. 

4.

 

If you are going to install the drivers from the disc insert it when advised by Windows. If you are 
going to use downloaded drivers, select “I don‟t have the disc. Show me other options.” 

5.

 

Browse to the folder where the drivers are stored and click next.  

6.

 

When the wizard is complete, click the close button. 

7.

 

The Found New Hardware wizard should appear again. When it does, follow steps 2-6 again for 
the second driver. 

 
If you are using another version of Windows or a Mac OS and require specific instructions for installing the drivers, they 
can be found at:  ftdichip.com/Documents/InstallGuides.htm. 

Summary of Contents for Copam



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands