UNIVIEW OET-213H User Manual Download Page 55

50 

external device is connected or external devices 
do not need O&M management. 

 

Bluetooth Mode: This option is displayed when 
the face recognition terminal is used with a smart 
lock via Bluetooth. 

 

Wiegand IC Card Mode: Select this option when 
the face recognition terminal connects to a card 
reader through RS232. 

Set this parameter based on actual scenes. 

NOTE! For RS485 and RS232 serial ports, Port Mode cannot be set to a gate mode at the same time.

 

Enable Security 
Module 

The configuration is not supported. 

RS485 Address 

The configuration is not supported. 

Baud Rate 

The configuration is not supported. Use the default value. 

Data Bits/

 

Stop 

Bits/

 

Parity/

 

Flow Control 

Keep the default values as follows: 

Data Bits: 8 

Stop Bits: 1 

Parity: None 

Flow Control: None 

NOTE! The parameters cannot be set when 

Port Mode

 is set to 

IC Card Mode

Enable Trans-
Channel 

It is used for internal debugging. Ignore it. 

 

(2) 

Configure serial port information based on actual scene configuration. 

(3) 

Click 

Save

 to complete the serial port configuration. 

(2)

 

Wiegand Interface 

When the face recognition terminal connects to an IC card reader, Wiegand interface information needs to be 
configured. Perform the following operations to complete the configuration: 

(1) 

Choose 

Setup

 > 

Common

 > 

Ports & Devices

 and click the 

Wiegand Interface

 tab. 

 

NOTE! 

 

Some devices support the input through only one or zero Wiegand interfaces and the configuration window for 
the Wiegand input interface is different for the devices. 

 

Some devices do not support the output through the Wiegand interface. In this case, the configuration window 
for the Wiegand output interface will not be displayed. 

 

The Wiegand interface configuration window is unavailable to ET-B31H-M@B with a built-in IC card reader. 

 

Figure7-23 

Wiegand Interface Configuration Window 

 

 

(2) 

Configure Wiegand interface information by referring to the table below. 

Summary of Contents for OET-213H


































































































Reviews: