background image

 

 

 

 

10

TROUBLESHOOTING

 

GUIDE 

 
 

  TROUBLE

 

 

  

POSSIBLE

 

CAUSE 

  REMEDY 

1. Slicer will 

not operate.

 

1.1 Electrical service 

down 

1.2 Knife guard knob 

not tight 

1.3 Circuit breaker 

tripped 

1.4 Bad switch  
1.5 Motor capacitor 

defective. 

1.6 Burned out motor

 

1.1 Check electrical service.   

Replace fuse or reset 
circuit breaker as 
necessary 

1.2 Tighten knob 
1.3 Reset circuit breaker 
1.4 Replace switch 
 
1.5 Replace capacitor  
1.6 Replace motor

 

2. Motor 

running,  
blade not 

2.1 Broken belt

 

2.1 Replace belt

 

3. Excessive 

noise. 

 

3.1 Blade contacting 

knife guard 

 
3.2 Deflector 

contacting blade 

 

 

3.1 Check for loose knife 

guard knob. Shim 
tapered bushing. 

 
3.2 Adjust deflector. 

 

4. Not cutting 

properly.

 

4.1 Dull blade or 

improperly 
sharpened blade. 

 
4.2 Soft cheese. 
 
4.3 Knife dirty with 

hard, dried-on 
product.

 

4.1  Sharpen blade 

following outlined 
procedures. 

 
4.2 Chill for best slicing 

results. 

 
4.3 Clean knife thoroughly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

04/09

Summary of Contents for 4509












Reviews: