Unitech UNI-335 Installation Manual Download Page 16

 

16

5

+

 

Panic with 

Ignition off 

Panic with 

Ignition on & off 

Panic with Ignition 

on & off Panic 

with No time limit. 

Without Panic 

function. 

6

+

 

Without Car

jack made

Active Car-jack mode 

Passive Car-jack 

mode 

 

7

+

 

With Dome light turns on 

& off after ignition off (45 

second door by-pass) 

With Dome light turns on 

after ignition off (45 

second poor by-pass) 

Without this 

feature 

 

8

+

 

Lock/Arm 

&UnIock/Disarm 

Confirmation Chirp

 

Lock/Arm Confirmation 

Only 

 

 

 

Exit:

 Turn Ignition to 'ON' position, or leave it for 15 seconds. parking light flashes five 

times will confirm exit. 

45 seconds Delay Door Ajar Error Chirp: 

This feature controls the error chirp that is generated if the system is armed with the door 

trigger active. This is useful in a vehicle that has along dome light delay after the door has 

been closed. If the system is armed before the dome light has turned off, the security 

system will generate the door trigger error chirp. Use this feature to disable the door open 

error chirp. 

With Dome light turns on after ignition off: 

Some vehicles turn on the dome light when ignition key is turned off. After remote start, 

with alarm on, a false alarm may occur when the run time elapses and the dome light 

comes on. To prevent this from happing, program Alarm Feature

 A-7 

to“ With Dome 

light turns on after ignition off (45 second door by-pass)". 

"A"-7-1: System at Arm mode ,as Ignition on /Off, will be delay 45secs to detect the doors 

 

"A"-7-2: System at Arm mode, as Ignition off will delay 45secs to detect the doors. 

"A"-7-3: As Ignition on/off, will not delay to detect the doors. 

 

ALARM FEATURE "B" PROGRAMMING: 

1

Turn the Ignition switch 

`ON/OFF' 3 TIMES 

and stay in the 

OFF Position

2

Push the Valet switch 

5 times

 (holding in on the 5

th

 push) until two chirps & two parking 

flashes and then release the valet switch. You are now in the Alarm feature 

"B" 

programming mode. 

3

Press and release the transmitter button corresponding to the feature you want to 

program. 

 

Press 

Transmitter 

Button 

One Chirp /    LED 

one pulse 

Factory Setting 

Default 

Two Chirps / LED 

two pulses 

Three Chirps / LED three 

pulses 

Four Chirps / 

LED four 

pulses 

1

 

Pathway 

illumination feature 

Parking light turns 

"on" for 30-second 

Parking light turns "on" for 30 

second upon an unlock 

 

Summary of Contents for UNI-335






























Reviews: