Unitech UNI-335 Installation Manual Download Page 15

 

15

 

Code learning: 

Note: 

This mode will only retain the 4 remote transmitters programmed. If the transmitter 

memory is exceeded, the security system will start deleting transmitters from memory in 

chronological order. 

1. Turn the Ignition 'switch

 'OFF/ON' 3 TIMES

 and stay in

 ON position 

  "Within 15 seconds". 

2. Push the Valet switch

 2 times

 and hold it on the 

2

nd

 push until a long chirp is heard then 

release the valet switch. You are now in the Transmitter programming mode. 

3. Press and hold b button3 of the transmitter until the siren responds with a 

confirming chirp, indicating the signal has been stored into memory. 

4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 

for each transmitter 

Exit:

Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 parking light flashes will 

confirm exit. 

 

Featurs Programming: 

ALARM FEATURE "A" PROGRAMMING: 

1. Turn the Ignition 'switch

 'ON/OFF' 3 TIMES 

and stay in 

OFF position 

2. Push the Valet switch 3 times (holding in on the 

3

rd

 push

) until one chirp & one parking 

flash. and then release the valet switch. You are now in the Alarm feature

 "A" 

programming mode. 

3. Press and release the transmitter button corresponding to the feature you want to 

program. 

    a. The siren chirps and LED pause will indicate previously setting. 

    b. The factory default settings is always [1] LED flash, [1] chirp. 

4 Depress the transmitter button to change the feature. Simple keep re-depressing the 

transmitter button until the system advances to your desired setting. 

5. Press the transmitter button corresponding to the feature you want to program. 

 

Press 

Transmitter 

Button 

One Chirp/LED one pulse

Factory Default Setting

 

Two Chirps/ 

LED two pulses 

Three Chirps/ 

LED three pulses 

Four Chirps/ 

LED four 

pulses 

1

 

Active arming 

Passive arming

 

Passive arming    without 

passive door locking 

Passive arming 

with passive door 

locking 

 

2

 

Automatic Rearm off 

Automatic 

Rearm on 

 

 

3

 

Instant Door Ajar error 

chirp 

45 seconds delay Door 

Ajarerror chirp. 

 

 

4

 

All Confirmation 

chirps on

 

Siren Confirmation 

chirp on only 

Horn Confirmation 

chirp on only 

All 

Confirmation 

chirps off 

PROGRANMMING

Summary of Contents for UNI-335






























Reviews: