background image

 

29

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

-Reorient or relocate the receiving antenna. 
-Increase the separation between the equipment and receiver. 
-Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 

-Consult the dealer or an experienced radio/TV technician for help. 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

1) this device may not cause harmful interference and 

2) this device must accept any interference received, including interference that may cause 

undesired operation of the device. 

 

Summary of Contents for UNI-335






























Reviews: