Unitech MS852Plus Auto Switching User Manual Download

Page: 47 / 99

- 32 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852Plus User’s Manual

3.3.9 Code 128

Code 128 On*

Default All Code 128

Settings

Code 128 Off

3.3.9.1 ISBT 128 Concatenation

In 1994 the International Society of Blood Transfusion (ISBT) ratified a

standard for communicating critical blood information in a uniform manner.

The use of ISBT formats requires a paid license. The ISBT 128 Application

Specification describes 1) the critical data elements for labeling blood products,

2) the current recommendation to use Code 128 due to its high degree of

security and its space-efficient design, 3) a variation of Code 128 that supports

concatenation of neigh-boring symbols, and 4) the standard layout for bar

codes on a blood product label. Use the bar codes below to turn concatenation

on or off. Default =Off.

Off*

Summary of Contents for MS852Plus Auto Switching


































































































Search results

Summary of Contents for MS852Plus Auto Switching

Reviews:

Related manuals for MS852Plus Auto Switching

Brands by name

Popular brands

Unitech MS852Plus Auto Switching, User Manual

Search results

Summary of Contents for MS852Plus Auto Switching

Reviews:

Related manuals for MS852Plus Auto Switching

Brands by name

Popular brands