Unitech MS852B Plus User Manual Download

Page: 117 / 169

- 101 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS852B Plus User’s Manual

3.2.13.5 EAN/JAN-13 Addenda Separator

When this feature is

, there is a space between the data from the bar code

and the data from the addenda. When turned

Off

, there is no space.

Default = On.

Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to

UPC-A/EAN-13 with Extended Coupon Code.

On*

Off

3.2.13.6 ISBN Translate

When On is scanned, EAN-13 Bookland symbols are translated into their
equivalent ISBN number format. Default = Off.

Off *

3.2.14 EAN/JAN-8

EAN/JAN-8 On*

Default All EAN/JAN-8
Settings

EAN/JAN-8 Off

Summary of Contents for MS852B Plus





































































































































































Search results

Summary of Contents for MS852B Plus

Reviews:

Related manuals for MS852B Plus

Brands by name

Popular brands

Unitech MS852B Plus, User Manual

Search results

Summary of Contents for MS852B Plus

Reviews:

Related manuals for MS852B Plus

Brands by name

Popular brands