manualshive.com logo in svg

UNIRAC EcoFoot5DTM, Installation Manual

Share
Download
UNIRAC EcoFoot5DTM Installation Manual Download Page 11

INSTALLATION GUIDE

PAGE

HIGH DENSITY 5-DEGREE

BALLAST RACKING SYSTEM

8

SYSTEM INSTALLATION STEPS

Step 1 – Install Pre-assembled Universal Clamps into Bases

•  Place Lower and Upper Universal Clamp into EcoFoot5D Base as shown. 
•  Push Clevis Pins completely into EcoFoot5D Base to secure Rocker.

Step 2 – Position Array 

•  Snap two chalk lines on roof denoting outside edges of the EcoFoot5D 

Bases, per project drawing. Start from the north or south edge. Ensure 
chalk lines are square. 

•  Place EcoFoot5D Bases in approximate position throughout the array.

Installation Tips

•  Only install Clamps where modules will rest. 
•  See Step 3 for correct placement and orientation of Clamps.

Installation Tips

•  As you build the array, panels will space the Bases. Roughly place a few 

rows of Bases at a time so 

that they are within reach of fi nal location.

Note: The Upper Clamp includes a post and nut to install the Wind 

Defl ector as shown in Step 6.

Summary of Contents for EcoFoot5DTM






























Reviews:

No comments

Brands by name

Popular brands

Load more brands