Unipulse F320 Operation Manual Download Page 32

Page: 32 / 129

3.CONNECTION

3-3. Connecting High / Low Limit Relays

• Connecting External Load

[ High limit relay ]

N/O

COM

Load

Varistor

Spark Killer

←

Inside Outside

→

F320

AC Power Supply

N/O

COM

←

Inside Outside

→

F320

[ Low limit relay ]

Spark Killer

←

Inside Outside

→

COM

N/O

Load

F320

DC Power Supply

N/O

COM

←

Inside Outside

→

F320

[ Low limit relay ]

Power
Supply

Connect a spark killer as

near the load as possible.

Connect a diode as

near the load as possible.

Power
Supply

CAUTION

Use within the rating (250V AC 0.5A).

Overvoltage and overcurrent may cause breakdown of the relay as well as

shortening its life.

It is recommended to connect a spark killer etc. to the connected load

according to AC/DC (refer to the connection examples). With a noise killer,

you can make the life of the relay longer as well as making it resistible against

noise.

Never short-circuit the load. Should you do it, the equipment will break down.

Summary of Contents for F320


































































































































Search results

Summary of Contents for F320

Reviews:

Related manuals for F320

Brands by name

Popular brands

Unipulse F320, Operation Manual

Search results

Summary of Contents for F320

Reviews:

Related manuals for F320

Brands by name

Popular brands