Unipulse F320 Operation Manual Download Page 28

Page: 28 / 129

3.CONNECTION

◇

Connecting a Lightning Surge Protector

To take measures against lightning surge, install a lightning surge protector.

EN61000-4-5 (lightning surge immunity) out of the EMC directives applies to

the F320 body and lightning surge protector in combination.

Lightning surge protector

For connecting the lightning surge protector, a
cable with an EU plug (optionally available) is
required.

* MAINTRAB MNT-1D is a trademark of

PHOENIX CONTACT.

MAINTRAB MNT-1D

F320

No lightning surge protector [MAINTRAB MNT-1D] is included as a

standard. It is optionally available (TSU01) in combination with a

250V AC high-voltage cable in EU outlet form (See below:

Standard product in Europe). For details, contact our sales

department.

Summary of Contents for F320


































































































































Search results

Summary of Contents for F320

Reviews:

Related manuals for F320

Brands by name

Popular brands

Unipulse F320, Operation Manual

Search results

Summary of Contents for F320

Reviews:

Related manuals for F320

Brands by name

Popular brands