background image

Error code table :

 

Red blink code of fault signal lamp (LED) 

Possible cause 

2 x blinks 

No establishment of flame at the end of the safety time (TSA) 
- Faulty or soiled flame detector
- Faulty or soiled fuel valves
- Poor adjustment of burner, no fuel
- Faulty ignition equipment

3 x blinks 

Air pressure switch (LP) faulty 

-

Loss of air pressure after specified time (t10)

-

- Air pressure switch (LP) welded in no-load position

4 x blinks 

Extraneous light on burner startup 

5 x blinks 

Time supervision air pressure switch (LP) 
- Air pressure switch (LP) welded in working position

6 x blinks 

Actuator position not reached 
-

Actuator 

faulty

-

Wrong adjustment of cam

-

Actuator defective or blocked

-

False 

connection

-

Misadjustment

7 x blinks 

Too many losses of flame during operation (limitation of repetitions) 
-

Faulty or soiled flame detector

-

Faulty or soiled fuel valves

-

Poor adjustment of burner

8 x blinks 

Free 

9 x blinks 

Free 

10 x blinks 

Wiring error or internal error, output contacts, other faults 

12 x blinks 

Valve proving (LT) 
- Fuel valve 1 (V1) leaking

13 x blinks 

Valve proving (LT) 
- Fuel valve 2 (V2) leaking

14 x blinks 

Error in connection with valve closure control POC 

15 x blinks 

Error code 

15 

Error code 22: Error of safety loop (SL) 

During the time the cause of fault is diagnosed, the control outputs are deactivated: 

-

Burner remains shut down

-

External fault indication (AL) at terminal X2-03, pin 3 steady on

Diagnostics of cause of fault is quit and the burner switched on again by resetting the burner control. Press the lockout reset button
(info button) for about 1 second (<3 seconds).

Summary of Contents for HTP90A





















































































Reviews: