Unified Brands Randell DPM Series Operator'S Manual Download Page 6

6          

800-621-8560

 

NOTICE:  FOOD LOSS IS NOT COVERED UNDER WARRANTY  

 

3.  Repairs  caused  by  abuse  such  as  broken  glass,  freight  damage, 

excessive force, or scratches and dents. 

4.  Electrical  component,  mechanical,  or  equipment  failure  due  to  water 

damage from cleaning or maintenance procedures. 

5.  Drawer repairs that are the result of improper drawer track installation. 

 
QUOTATIONS 
Verbal  quotations  are  provided  for  customer  convenience  only  and  are 
considered  invalid  in  the  absence  of  a  written  quotation.    Written  quotations 
from Randell are valid for 30 days from quote date unless otherwise specified.  
Randell assumes no liability for dealer quotations to end-users. 
 
SPECIFICATION & PRODUCT DESIGN 
Due to continued product improvement, specification and product design may 
change  without  notice.    Such  revisions  do  not  entitle  the  buyer  to  additions.  
Changes or replacements for previously purchased equipment. 
 
SANITATION REQUIREMENTS 
Certain  areas  require  specific  annotation  requirements  other  than  N.S.F.  & 
U.L.  standards.    Randell  must  be  advised  of  these  specifications  before 
fabrication of equipment.  In these special circumstances, a revised quotation 
may  be  required  to  cover  additional  costs.    Failure  to  notify  Randell  before 
fabrication holds the dealer accountable for all additional charges. 
 
CANCELLATIONS 
Orders 

canceled 

prior 

to 

production 

scheduling 

entered 

into 

engineering/production  and  cancelled  are  subject  to  a  cancellation  charge 
(contact factory for details). 
 
STORAGE CHARGES 
Randell  makes  every  effort  to  consistently  meet  our  customer’s  shipment 
expectations.    If  after  the  equipment  has  been  fabricated,  the  customer 
requests delay in shipment, and warehousing is required: 
 

1.  Equipment  held for  shipment  at  purchasers  request for  a  period  of  30 

days  beyond  original  delivery  date  specified  will  be  invoiced  and 
become immediately payable. 

2.  Equipment  held  beyond  30  days  after  the  original  delivery  date 

specified will also include storage charges. 

 
SHIPPING & DELIVERY 
Randell  will  attempt  to  comply  with  any  shipping,  routing  or  carrier  request 
designated  by  dealer,  but  reserves  the  right  to  ship  merchandise  via  any 
responsible  carrier  at  the  time  equipment  is  ready  for  shipment.    Randell  will 
not  be  held  responsible  for  any  carrier  rate  differences;  rate  differences  are 
entirely  between  the  carrier  and  purchaser.    Point  of  shipping  shall  be 
determined  by  Randell  (Weidman,  MI/Jackson,  MS).    At  dealer’s  request, 
Randell  will  endeavor  whenever  practical  to  meet  dealer’s  request.    Freight 
charges to be collect unless otherwise noted. 
 
 
 

Summary of Contents for Randell DPM Series



























Reviews: