background image

User’s Manual                                                                                                                                                           Series DC Electronic Load 

Instruments.uni-trend.com

                                                                                                                                                                                   

33

 / 

33

 

 

external surface of the instrument:   

a. Please use a soft cloth to wipe the dust outside the instrument. 
b. When cleaning the LCD screen, please pay attention and protect the transparent LCD screen.   
c. When cleaning the dust screen, use a screwdriver to remove the screws of the dust cover and then   

remove the dust screen. After cleaning, install the dust screen in sequence. 

d. Please disconnect the power supply, then wipe the instrument with a damp but not dripping soft cloth.   

Do not use any abrasive chemical cleaning agent on the instrument or probes. 

    Warning     

Please  confirm  that  the  instrument  is  completely  dry  before  use,  to  avoid  electrical  shorts  or  even 
personal injury caused by moisture.

 

 

11.2 

Appendix B Warranty Overview

 

UNI-T (UNI-TREND TECHNOLOGY (CHINA) CO., LTD.) ensures the production and sale of products, from 
authorized dealer’s delivery date of three years, without any defects in materials and workmanship. If 
the product is proven to be defective within this period, UNI-T will repair or replace the product in 
accordance with the detailed provisions of the warranty. 

 

To  arrange  for  repair  or  acquire  warranty  form,  please  contact  the  nearest  UNI-T  sales  and  repair 
department. 

 

In addition to permit provided by this summary or other applicable insurance guarantee, UNI-T does 
not provide any other explicit or implied guarantee, including but not limited to the product trading and 
special purpose for any implied warranties. 

 

In any case, UNI-T does not bear any responsibility for indirect, special, or consequential loss.

 

11.3 

Appendix C Contact Us 

If the use of this product has caused any inconvenience, if you in mainland China you can contact 
UNI-T company directly. 
Service  support:  8am  to  5.30pm  (UTC+8),  Monday  to  Friday  or  via  email.  Our  email  address  is 
[email protected] 
For product support outside mainland China, please contact your local UNI-T distributor or sales 
center. 
Many  UNI-T  products  have  the  option  of  extending  the  warranty  and  calibration  period,  please 
contact your local UNI-T dealer or sales center. 

 

To obtain the address list of our service centers, please visit our website at URL: http://www.uni-
trend.com 

 

Summary of Contents for UTL8200+ Series


































Reviews: