background image

Service Manual                                                                                                                                                                                                                                            UTG1000X Series 

Instruments.uni-trend.com                                                                                                                                                                                                                               

 

4

 / 

20

 

 

Safety Signs 

 

 

Danger 

Indicates a warning of a possible electric shock hazard that could 
result in personal injury or death. 

 

Warning 

Indicates a point requiring caution, which may result in personal 
injury or damage to the instrument. 

 

Caution 

Indicates a potentially hazardous condition that requires following a 
procedure or condition that may damage the instrument or other 
equipment; if a "Caution" sign is indicated, all conditions must be met 
before continuing to operate. 

 

Notice 

Indicates a potential problem, a procedure, or a condition that needs 
to be followed, which may cause the instrument to function 
improperly; if the "Caution" mark is marked, all conditions must be 
met to ensure that the instrument can function normally. 

 

Alternate 
current 

Instrument AC, please confirm the regional voltage range. 

 

Direct current 

Instrument direct current, please confirm the regional voltage range. 

 

Grounding 

Frame, chassis ground terminal. 

 

Grounding 

Protective earth terminal. 

 

Grounding 

Measure the ground terminal. 

 

Close 

The main power is off. 

 

Open 

The main power is turned on. 

 

Power supply 

Standby power, when the power switch is turned off, the instrument 
is not completely disconnected from the AC power source. 

CAT I 

A secondary electrical circuit connected to a wall socket through a 
transformer or similar device, such as electronic equipment. 
Electronic equipment with protective measures, any high-voltage 
and low-voltage circuits, such as copiers inside the office, etc. 

CAT II 

CATII: The primary electrical circuit of electrical equipment 
connected to the indoor socket through the power cord, such as 
mobile tools, home appliances, etc. Household appliances, portable 
tools (electric drills, etc.), household sockets, and sockets that are 
more than 10 meters away from Category III lines or 20 meters away 
from Category IV lines. 

CAT III 

Primary  circuits  of  large  equipment  directly  connected  to  the 
distribution  panel  and  circuit  connections  between  the  distribution 
panel and socket outlets (three-phase distribution circuits including 
individual  commercial  lighting  circuits).  Equipment  with  fixed 
positions, such as multi-phase motors, and multi-phase gate boxes; 
lighting equipment and lines inside large buildings; machine tools and 
power distribution panels at industrial sites (workshops), etc. 

 

Summary of Contents for UTG1000X Series





















Reviews: