UNAOHM
EP2500 (Rev. 0)
23
To access to MOTOR submenu proceed as follows:
•
Position Shaft Encoder to MOTOR.
•
Press
↵
ENTER
The available operating commands are as follows:
•
STOP MOTOR. Stops the motor and, therefore, the dish steering. Press 0 on the alphanumeric
keypad.
•
START MOTOR EAST. Starts dish steering towards east. Press 1 on the alphanumeric keypad.
•
START MOTOR WEST. Starts dish steering towards west. Press 2 on the alphanumeric keypad.
•
DISABLE LIMITS. Disengages the set steering limits towards both EAST and WEST. Press 3 on
the alphanumeric keypad.
•
SET EAST LIMIT. Allows a steering limit towards EAST to be set on the dish. Pressing key 1
steers the dish towards EAST, pressing 0 stops the dish at the desired limit, pressing 4 stores that
limit.
•
SET WEST LIMIT. Allows a steering limit towards WEST to be set to the dish. Pressing key 2
steers the dish towards WEST, pressing 0 stops the dish at the desired limit, pressing 5 stores that
limit.
•
STORE MTR SAT POS. Pressing key 6 allows the dish position to be stored inside the motor
setting locations. Before pressing key 6, select the setting location of the motor where you wish to
store the dish position, as follows:
•
Mark STORE MTR SAT POS via the shaft encoder.
•
Press
↵
ENTER
.
•
Mark the desired motor setting location via the shaft encoder.
•
Press
↵
ENTER
or
BACK
to confirm.
•
RECALL MTR SAT POS. Pressing key 7 allows any of the stored dish positions to be recalled.
Before pressing key 7, select the motor setting location to recall the dish position from, as follows:
1.
Mark RECALL MTR SAT POS via the shaft encoder.
2.
Press
↵
ENTER
.
3.
Mark the desired motor setting location via the shaft encoder.
4.
Press
↵
ENTER
or
BACK
to confirm.
•
START EAST TO. Pressing key 8 allows the dish to be steered towards EAST for a certain time or
a certain number of steps (regardless of the motor features).
If TIME mode has been set, an arrow will be shown close to the letter T; likewise, the letter S will
have an arrow shown close to it if STEP mode has been set. Before pressing key 8, set the seconds
the dish should be steered for (TIME mode) or the number of steps to steer the dish for (STEP
mode), as follows:
1.
Mark START EAST TO via the shaft encoder.
2.
Press
↵
ENTER
. If the cursor is not on the desired line (TIME or STEP) press
↵
ENTER
again.
3.
Spin the shaft encoder in order to set the desired TIME (from 1 to 99 seconds) or STEP (from step 1
to 99).
4.
Press
↵
ENTER
or
BACK
to confirm.
•
START WEST TO. Pressing key 9 allows the dish to be steered towards WEST for a certain time or
a certain number of steps (regardless of the motor features).
If TIME has been set, an arrow will be shown close to the letter T; likewise, the letter S will have an
arrow shown close to it if STEP has been set. Before pressing key 9, set the seconds the dish should
be steered for (TIME mode) or the number of steps to steer the dish for (STEP mode), as follows:
1.
Mark START WEST TO via the shaft encoder.
2.
Press
↵
ENTER
If the cursor is not on the desired line (TIME or STEP) press
↵
ENTER
again.
3.
Spin the shaft encoder in order to set the desired TIME (from 1 to 99 seconds) or STEP (from step 1
to 99).
4.
Press
↵
ENTER
or
BACK
to confirm.
•
RECALCULATE SAT POSITION. All sat positions stored inside any of the motor setting location
can be recalculated simply by pressing the decimal point key.