background image

UNAOHM 

EP2500 (Rev. 0)                                                                                                                                                   

1

 

 

INDEX 

 

1  SAFETY PRECAUTIONS & GENERAL WARNINGS............................................................4 

1.1 SAFETY 

PRECAUTIONS................................................................................................. 4 

1.2 GENERAL 

WARNINGS ................................................................................................... 5 

1.3 MAINTENANCE ............................................................................................................... 5 
1.4 NOTES................................................................................................................................ 5 

2 INTRODUCTION ..........................................................................................................................6 

3 MAIN 

CHARACTERISTICS .......................................................................................................7 

3.1 SPECIFICATIONS............................................................................................................. 7 

4 ACCESSORIES............................................................................................................................11 

4.1 STANDARD 

ACCESSORIES ......................................................................................... 11 

4.2 OPTIONALS .................................................................................................................... 11 
4.3 ANCILLARY 

INSTRUMENTS ...................................................................................... 11 

5  CONTROLS and CONNECTIONS ...........................................................................................14 

5.1 FRONT 

PANEL................................................................................................................ 14 

5.2 LEFT 

SIDE 

PANEL ......................................................................................................... 15 

5.3  RIGHT SIDE PANEL....................................................................................................... 15 

6 POWER 

SUPPLY ........................................................................................................................16 

6.1  PREPARING THE INSTRUMENT FOR USE ............................................................... 16 
6.2 BATTERY 

REPLACEMENT .......................................................................................... 16 

6.3  POWER SUPPLY MODES.............................................................................................. 18 

6.3.1 

Low Battery Indication.............................................................................................. 18 

6.4  11VDC. AUXILIARY OUTPUT SOURCE OF POWER ............................................... 18 

7 OPERATING 

MODE ..................................................................................................................19 

7.1 DEFAULT 

CONDITIONS ............................................................................................... 19 

7.2  ON SCREEN DISPLAY................................................................................................... 19 

7.2.1 Screen 

Saver.............................................................................................................. 19 

7.3  VOLUME, BRIGHTNESS & CONTRAST ADJUSTMENTS ....................................... 19 
7.4  USE of DIGIT KEYS, SHAFT ENCODER, ARROWS     for NUMBER ENTRIES 19 
7.5 RESET .............................................................................................................................. 20 
7.6 TUNING ........................................................................................................................... 20 

7.6.1 

SAT Tuning by Means of Transponder Frequency ................................................... 20 

7.7 ATTENUATOR................................................................................................................ 21 
7.8  LNB. REMOTE POWER SUPPLY TO LNB .................................................................. 21 
7.9  22 kHz COMMAND SIGNAL ......................................................................................... 21 
7.10 DiSEqC ............................................................................................................................. 22 

7.10.1  How to Engage the 22 kHz Tone............................................................................... 22 
7.10.2  Transmission of a DiSEqC 1.1 Command ................................................................ 22 
7.10.3  DiSEqC 1.2 for Steerable Dishes.............................................................................. 22 
7.10.4  User-Defined DiSEqC 1.1 Commands...................................................................... 24 

7.11 MEASUREMENT BANDWIDTH................................................................................... 25 
7.12 FUNCTION ...................................................................................................................... 25 
7.13  SPECTRUM ANALYSER FUNCTION.......................................................................... 25 

7.13.1 Video 

Filter ............................................................................................................... 26 

7.14  SPECTRUM EXPANDED FUNCTION.......................................................................... 26 

Summary of Contents for EP2500


































































Reviews: