Ultra Start 650 Series Install Manual Download Page 5

1 - Cycle the Ignition Key On/Off On/Off On. 
(Leave the key in the ON position)

2 - Press and release the Program Switch 1 time. 

(*The Siren will chip to confirm that the system has entered Program Mode.)

*If the siren does not chirp repeat steps 1 & 2.

3 - Select the Program Menu.
-Press the Lock Button To Enter Menu 1.
-Press the Unlock Button to Enter Menu 2.

(*The Siren will chip to confirm that the system has entered the Menu.)

See the following page for Program Menus and Settings.

4 - Press and Release the Program Switch to advance through the settings.

(

Each setting is Confirmed by siren chirps & LED flashes)

5 - Press and hold the Program Switch to change the setting.

(

Confirmed by Siren Chirps*)

   * One Chirp = Setting 1
  **Two Chirps = Setting 2
***Three Chirps = Setting 3

6 - 

To exit Program Mode, turn ignition key off.

(Confirmed by Long Siren Chirp)

  

ENTERING PROGRAM MODE

SYSTEM PROGRAMMING - 

Menu 1

PAGE 4

650 SERIES

INSTALL  MANUAL

PROGRAM MODE

SYSTEM PROGRAMMING - 

Menu 1

PAGE 5

650 SERIES

INSTALL MANUAL

PROGRAM MODE

1 - Cycle the Ignition Key On/Off On/Off On. 
(Leave the key in the ON position)

2 - Press and release the Program Switch 1 time. 

(*The Siren will chip to confirm that the system has entered Program Mode.)

*If the siren does not chirp repeat steps 1 & 2.

3-  Press and Hold the program switch until the siren chirps 3 times.
      (The system is now reset to default settings)

 SYSTEM RESET

SETTING #

LED FLASHES

2

3

1

VALET

SETTINGS

SECURE VALET

15 SECONDS

STANDARD VALET

8 SECONDS

OPTION 3

3 CHIRPS

OPTION 1

1 CHIRP

OPTION 2

2 CHIRPS

PARK LIGHT

OUTPUT

AUX CHANNEL 5

OPTIONS

30 SECOND ON

FOR DISARM

0.75 SEC

PULSED OUTPUT

POS TRUNK 

RELEASE OUTPUT

LATCHED

IGNITION ON RESET

NORMAL OPERATION

ACTIVE WHILE 

BUTTON IS HELD

SETTING

DESCRIPTION

SETTING #

LED FLASHES

1

2

3

4

5

6

7

IGNITION

AUTO-LOCK

IGNITION AUTO-LOCK & 

UNLOCK ENABLED

IGNITION AUTO-LOCK

ONLY

OPTION 3

3 CHIRPS

IGNITION AUTO-LOCK

DISABLED

OPTION 1

1 CHIRP

OPTION 2

2 CHIRPS

SIREN SETTINGS

DOOR LOCK

OPTIONS

DOOR LOCK

PULSE TIMES

SHOCK SENSOR

SETTINGS

PASSIVE ARMING

PASSIVE 

DOOR LOCKS

SIREN CHIRPS

DISABLED

DOUBLE UNLOCK /  

SINGLE LOCK PULSES

0.25 SECOND

PULSES

SENSOR DISABLED

FULL

PASSIVE ARMING

PASSIVE DOOR LOCKS

DISABLED

SIREN CHIRPS

ENABLED

DOUBLE LOCK / 

SINGLE UNLOCK PULSES

3 SECOND

PULSES

SENSOR ENABLED

PASSIVE SAFETY

REARM ONLY

PASSIVE DOOR LOCKS

ENABLED

SIREN CHIRPS

ENABLED

SINGLE UNLOCK / 

SINGLE LOCK PULSE

S

0.75 SECOND

PULSES

ALL PASSIVE ARMING

DISABLED

SETTING

DESCRIPTION

PROGRAM MODE 1

PROGRAM MODE 2

4

5

HORN OUTPUT 

TIMING

AUX CHANNEL 3

OPTIONS

50MS HORN 

OUTPUT

0.75 SEC

PULSED OUTPUT

20MS HORN

OUTPUT

LATCHED

IGNITION ON RESET

10MS HORN 

OUTPUT

ACTIVE WHILE 

BUTTON IS HELD

6

ANIT-CAR JACK MODE

OPTIONS

CAR JACK MODE 1

CAR JACK MODE 2

CAR JACK MODE 

DISABLED

7

HORN/ AUX CHANNEL

 4 OUTPUT

0.75 SEC

PULSED OUTPUT

ACTIVE WHILE BUTTON 

IS HELD

HORN OUTPUIT

8

HOOD PIN INPUT

TRAILER DISCONNECT

HOOD PIN INPUT

9

2ND UNLOCK/ (-) WHEN 

DISARMED

GROUND WHEN 

DISARMED

PRIORITY DOOR 

UNLOCK

Summary of Contents for 650 Series





















Reviews: