background image

SYSTEM PROGRAMMING - 

Menu 1

Applicated Security Technologies, Inc. ("AST") promises to the original purchaser to repair or replace with 
a comparable reconditioned model any AST control module ("module") excluding without limitation the any 
other accessories, including but not limited to the antenna, remote, siren and wiring harness, proves to be 
defective in workmanship or material under reasonable use during the lifetime of the vehicle it was 
originally installed, provided the following conditions have been met: the module was professionally 
installed and serviced by an authorized AST dealer; the unit will be professionally reinstalled in the vehicle 
in which it was originally installed by an authorized AST dealer; the warranty information card was sent to 
AST within 10 days of the original installation date.  Any warranty returns include a warranty return 
authorization number issued by AST, original bill or sale and be pre-paid shipped directly to AST.  After an 
initial period of 2 years from the date of installation, AST reserves the right, at its sole discretion, to charge 
a warranty processing fee of $30.00 USD.  AST does not cover the cost for return freight on warranty 
items, this cost is the sole responsibility of the purchaser.

All components included with the original packaged unit other than the module, including but not limited to 
the siren, antenna and the remote transmitters, carry a one-year warranty from the date of purchase of the 
same. Any warranty returns on components must include a warranty return authorization number issued 
by AST, original bill or sale and be pre-paid shipped directly to AST.  This warranty is non-transferable and 
is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten 
(10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is 
defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended 
purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, 
installation or other causes not arising out of defects in materials or construction. The warranty does not 
cover damage to the unit caused by installation or removal of the unit. AST, at its sole discretion, will 
determine what constitutes excessive damage and may refuse the return of any unit with excessive 
damage, including, but not limited to, overloading, moisture and physical damage.

To the maximum extent allowed by law, any and all warranties are excluded by the manufacturer and each 
entity participating in the stream of commerce therewith. This exclusion includes but is not limited to, the 
exclusion of any and all warranty of merchantability and/or any and all warranty of fitness for a particular 
purpose and/or any and all warranty of non-infringement or patents, in the United States of America and/or 
abroad. Neither the manufacturer or any entities connected therewith shall be responsible or liable for any 
damages whatsoever, including but not limited to, any consequential damages, incidental damages, 
damages for loss of time, loss of earnings, commercial loss, loss of economic opportunity and the like. 
Notwithstanding the above, manufacturer does offer a limited warranty to replace or repair the control 
module as describe above.

Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation 
on how long an implied warranty will last or the exclusion or limitation of incidental or consequential 
damages. This warranty gives you specific legal rights, and you may also have other rights, which vary 
State to State.

SYSTEM PROGRAMMING - 

Menu 1

PAGE 18

650 SERIES

INSTALL  MANUAL

QUICK VIEW OPERATIONS

SYSTEM PROGRAMMING - 

Menu 1

PAGE 19

650 SERIES

INSTALL MANUAL

WARRANTY

1 SEC

1

LOCK / ARM ALARM

3 SEC

1

ACTIVATE PANIC

PRESS THEN RELEASE 

THEN PRESS & HOLD

1

ACTIVATE CONSTANT LOCK OUTPUT 

**

BUTTON PRESS

CHIRP / 

FLASH

SYSTEM FUNCTION

BUTTON

1 SEC

2

UNLOCK / DISARM

1 SEC

WHILE ALARM IS 

TRIGGERED

NONE

TURNS OFF SIREN BUT ALARM IS 

STILL ARMED

1 SEC

3

UNLOCK / DISARM

ALARM EVENT IN MEMORY

see alarm event memory chart

PRESS & HOLD FOR 1 - 

5 SEC

1

ACTIVATES AUX OUTPUT

** PROGRAMMABLE OUTPUT - CHECK WITH INSTALLATION CENTER FOR DETAILS

+

+

+

FOR DETAILED OPERATIONS AND INSTRUCTIONS PLEASE SEE OWNERS 

GUIDE

SECOND CAR OPERATION/ PADLOC. SEE TRANSMITTER PROGRAMMING FOR 

INFORMATION ON PROGRAMMING THIS FEATURE.

Summary of Contents for 650 Series





















Reviews: