background image

Auto Tach Learn

1) Turn the ignition key to the “ON” position. (The park lights will turn on*).
2) Start the vehicle with the key, The LEDs on the antenna will turn on if a proper tach
     signal is detected**, then after 30-35 seconds the park lights will flash and the siren 
     will chirp twice to confirm Tach Learn. 

* If the park lights do not turn on check for proper connection on the BLUE ignition
   wire at the 6-pin connector. This wire should be connected to the vehicle main
   ignition wire and must not turn off during the start position. If the ignition
   connection is good reset the system and repeat step #1. 
 ** If the LEDs do not come on during tach learn, a proper tach signal was not
     detected.

If not tach learned the system will flash the park lights seven times when the start button
is pressed. The system must be Tach Learned before remote starting.

Note:

 If the park lights do not flash in auto tach learn mode it may be necessary to 

          connect to a different tach source. It is important the ignition output from the
          remote starter is connected to a wire that does not turn off in the crank position. 

The remote starter will not tach learn if connected to the wrong wire.

          For best results connect the tach wire to the coil pack or to a fuel  injector wire. 

New - If the original Tach source is changed a system reset must be preformed 
before a new tach signal can be learned to the system. This does not apply if the 
Quick Learn feature is being used. See page 15 for system reset.

Your Basic Install Is Complete!

NOTES:
    1)  If the vehicle does not start when the remote starter is activated, check if the
     park lights are flashing a diagnostic code. See diagnostic chart.
    2)  If the vehicle still does not start, check all connections and check for factory

Anti-Theft system.

Note: If the vehicle is not starting correctly it may be necessary to adjust the tach.
          See page 13 for Quick Tach Learn. 

Page 12

INSTALLATION MANUAL

REMOTE VEHICLE STARTER

Summary of Contents for 45 SERIES

























Reviews: