SYSTEM PROGRAMMING -
Menu 1
PAGE 2
95 SERIES
INSTALL MANUAL
TABLE OF CONTENTS
QUICK VIEW WIRING DIAGRAM..........................................................3-4
Connector Pin Configuration
Antenna Connector
Park Light Jumper
NOTES........................................................................................................5
Addition Installation Notes
QUICK VIEW PROGRAMMING..............................................................6-9
Enter Program Mode
System Reset
Transmitter Programming
Menu 1,2,3 & 4 Quick View
Auto Tach Learning
Manual Tach Learn (Vehicles without start wire)
SYSTEM WIRING DETAILS................................................................10-14
Connector Views
Wiring Description
PROGRAM MENUS............................................................................15-23
Program Menu 1 Detailed
Program Menu 2 Detailed
Program Menu 3 Detailed
Program Menu 4 Detailed
DOOR LOCK DIAGRAMS..................................................................24-25
Relay Diagrams
SHOCK SENSOR (ALARM MODELS)....................................................26
Entering Adjustment Mode
Shock Sensor Adjustment
QUICK VIEW OPERATIONS CHART.......................................................27
Basic Operations
Service Mode/ Emergency Override
TRANSMITTER PROGRAMMING...........................................................28
Adding/ Reprogramming Transmitter
Second Car Operation & PAD LOCK
FAULT CODES.........................................................................................29
Feedback From the 2way Remote
ALARM TRIGGERS..................................................................................30
Feedback From the 2way Remote
DIAGNOSTICS..........................................................................................31
Diagnostic Chart
Diagnostic Memory
CONTACT INFORMATION.......................................................................32
SYSTEM PROGRAMMING -
Menu 1
PAGE 3
95 SERIES
INSTALL MANUAL
QUICK VIEW WIRE DIAGRAM
1
5
3
2
4
6
1
2
3
4
5
6
7
8
9
10
11
12
13
1
3
2
4
OUTPUT TO ACTIVATE
IGNITION CIRCUIT
THE VEHICLES
SELECTABLE OUTPUT* (DEFAULT 2ND IGN)
12VOLT/ 30 AMP MAIN POWER INPUT
OUTPUT TO ACTIVATE THE VEHICLES STARTER CIRCUIT
12VOLT/ 30 AMP MAIN POWER INPUT
OUTPUT TO ACTIVATE
ACCESSORY CIRCUIT
THE VEHICLES
SYSTEM GROUND INPUT
SELECTABLE PARK LIGHT OUTPUT (DEFAULT POSITIVE)
(+) SIREN OUTPUT / (-) HORN OUTPUT
AUXILIARY 1 OUTPUT/ PROGRAMMABLE OUTPUT.
(-) 2ND ACCESSORY/ PROGRAMMABLE AUXILIARY 2 OUTPUT
AUXILIARY OUTPUT TO ACTIVATE TRUNK RELEASE
REARM OUTPUT (PULSE WITH LOCK & AFTER START)
NEGATIVE SECOND START OUTPUT
DISARM OUTPUT (PULSE WITH UNLOCK & BEFORE START)
POSITIVE DOOR INPUT (+ WHEN DOOR OPENED)
DIESEL WAIT TO START (+ OR - INPUT) PROGRAMMABLE
TACH DETECTION INPUT (CONNECT TO COIL, INJECTOR...)
BRAKE SWITCH INPUT (12VOLT WHEN BRAKE IS PRESSED)
HOOD PIN SWITCH (GROUND WHEN HOOD IS OPENED)
PARK BRAKE INPUT (-) (”M” SERIES ONLY)
NEGATIVE DOOR INPUT (- WHEN DOOR OPENED)
Status LEDs
Program Button
* The selectable output can be changed in the program mode to output as a 2nd Accessory or 2nd Start output.
Default output is second ignition.
**This output does not change back to 2nd Ignition upon reset**
**Siren output on alarm models and horn honk output on starter models.
***A “M” series remote starter must be used when installing on a manual transmission vehicle.
NEVER
INSTALL AN AUTOMATIC REMOTE START IN A MANUAL VEHICLE!!
**** The door pin connections are used on Manual Transmission and Alarm Models Only.
THE DOOR DIN CONNECTION MUST BE CONNECTED FOR PASSIVE ARMING ON THE 3295.
BLACK
WHITE
ORANGE
BROWN**
BLUE
WHITE*
RED
YELLOW
RED
GREEN
WHT/VIOLET
ORANGE/WHT
RED/WHITE
YELLOW
GRAY
BROWN
PURPLE****
BLUE
BLUE/WHITE
GRN/WHITE
GREEN****
PINK
BLK/WHT***
(-) STARTER KILL/ ANTI-GRIND OUTPUT
