SYSTEM PROGRAMMING -
Menu 1
PAGE 20
95 SERIES
INSTALL MANUAL
PROGRAM MODE
CHANGE SETTING 4 -
GOTO SETTING 5 -
PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 4- SIREN OPTIONS
THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED
4 CHIRP
4X
1 CHIRP
2 CHIRP
3 CHIRP
SETS OPTION 1 - 30 SECOND DURATION-
The siren will activate for 30 seconds
when the alarm is activated.
SETS OPTION 2 – PULSED OUTPUT-
The siren output will pulse when activated.
(+) horn activation)
SETS OPTION 3 – 60 SECOND DURATION- The siren will activate for 30 seconds
when the alarm is activated. (DEFAULT)
PRESS
1 TIME
1 CHIRP
2 CHIRP
3 CHIRP
CHANGE SETTING 2 -
GOTO SETTING 3 -
PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 2-SPECIAL DOOR LOCK OPTIONS
THE SIREN WILL CHIRP 2 TIMES WHEN SETTING 2 IS SELECTED
2 CHIRP
PRESS
1 TIME
2X
1 CHIRP
2 CHIRP
3 CHIRP
SETS OPTION 1 –TYPE 2 -
The doors will unlock before remote start, lock when
remote starter starts and again when the remote start shuts down.
SETS OPTION 2 –
RE-LOCK-
The doors will automatically lock when the remote
starter shuts down.
SETS OPTION 3 – NORMAL OPERATION- No additional door lock or door
unlock pulses. (DEFAULT)
ENTERING PROGRAM MODE 3
CHANGE SETTING 1 -
GOTO SETTING 2 -
PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 1- SELECTABLE OUTPUT
THE SIREN WILL CHIRP 1 TIME WHEN SETTING 1 IS SELECTED
1 CHIRP
PRESS
1 TIME
1X
1 CHIRP
2 CHIRP
3 CHIRP
SETS OPTION 2 –SECOND ACCESSORY-
The white wire on the 6-pin connector
acts as a Second Accessory output.
SETS OPTION 3 –SECOND IGNITION- The white wire on the 6-pin connector
acts as a Second Ignition output. (DEFAULT)
SETS OPTION 1 – SECOND STARTER-
The white wire on the 6-pin connector acts
as a Second Starter output.
ON/OFF - ON/OFF - ON
(Leaving the key ON)
IGNITION KEY
Press and release 1 time
PROGRAM SWITCH
1 CHIRP
Confirming
Program Mode
SIREN CHIRP
Press START
Button to
Select Menu 3
REMOTE BUTTON
SYSTEM PROGRAMMING -
Menu 1
PAGE 21
95 SERIES
INSTALL MANUAL
PROGRAM MODE
1 CHIRP
SETTING 3-GAS/ DIESEL MODE
THE SIREN WILL CHIRP 3 TIMES WHEN SETTING 3 IS SELECTED
3 CHIRP
PRESS
1 TIME
3X
CHANGE SETTING 3 -
GOTO SETTING 4 -
PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
2 CHIRP
3 CHIRP
CON'T ON NEXT PAGE
SETS OPTION 1 – NEGATIVE-
The system will wait for the negative wait to start input
to turn off. (Starter will activate after 30seconds)
SETS OPTION 2 –
15 SECOND DELAY-
The system will wait for 15 seconds before
activating the starter motor.
SETS OPTION 3 – GAS/POSITVE- If 12 volts present on the wait to start input
the system will wait for up to 30 seconds then start. (DEFAULT)
ENTERING PROGRAM MODE 3
CHANGE SETTING 4 -
GOTO SETTING 5 -
PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 4- RE-ARM OPTIONS
THE SIREN WILL CHIRP 4 TIMES WHEN SETTING 4 IS SELECTED
4 CHIRP
PRESS
1 TIME
4X
1 CHIRP
2 CHIRP
3 CHIRP
SETS OPTION 1 - TYPE 2-
The rearm output pulses only when the lock button is
pressed.
SETS OPTION 2 – AFTER START-
The re-arm output will pulse after the remote
start starts the vehicle (DEFROST/ HEATED SEAT)
SETS OPTION 3 – REARM- Pulsed output when the doors are locked and after
remote start shutdown. (DEFAULT)
CHANGE SETTING 5 -
GOTO SETTING 6 -
PRESS & RELEASE THE VALET SWITCH
PRESS & HOLD THE VALET SWITCH UNTIL THE SIREN CHIRP(S)
SETTING 5- RUN TIME
THE SIREN WILL CHIRP 5 TIMES WHEN SETTING 5 IS SELECTED
5 CHIRP
PRESS
1 TIME
5X
1 CHIRP
2 CHIRP
3 CHIRP
SETS OPTION 1 – 4 MINUTES-
The system will run for approximately 4 minutes
then shut off.
SETS OPTION 2 – 45 MINUTES-
The system will run for approximately 45 minutes
then shut off.
SETS OPTION 3 – 15 MINUTES- The system will run for approximately 15
minutes then shut off. (DEFAULT)
