background image

PAGE 25                                                                                                  

INSTALL GUIDE

                                                                                                                                 

Very Important!

 

Do not set Reservation Mode if the vehicle is occupied.

 

       

Manual transmission remote starters must be set into Reservation Mode before 
the remote starter will activate.  The activation type of Reservation Mode is 
determined when the system is installed. 

Auto Reservation Mode (Default)  
Step 1     -

 While the vehicle is running, place into neutral and apply the park brake. 

Step 2*

    

-

 Press and release the brake pedal twice. The park lights will flash twice, 

                  the siren or horn (opt.) will chirp twice and the doors will unlock (opt.).

Step 3

     

-

 Turn the ignition key off and the vehicle will continue running.

Step 4**  -

 Within 30 seconds, exit the vehicle and close all the doors. The vehicle will

                  then shut off .

Manual Reservation Mode (Optional)
Step 1     - 

While the vehicle is running with the key, place transmission into neutral 

                  and apply the park brake.

Step 2     -

 Press and release the     button. The park lights will flash twice, the siren

                  or horn (opt.) will chirp twice and the doors will unlock (opt.).

Step 3     -

 Turn the ignition key off and the vehicle will continue running. 

Step 4     - 

Exit the vehicle and close all the doors. 

Step 5**  -

 Press and hold the     button for 3 seconds, the vehicle will then shut off.

*   

If the park lights 

do not

 flash and stay on or the siren (horn optional) chirps a third 

     time, repeat 

Step 2

.

** If the vehicle has dome light delay, the vehicle may stay running until the dome   
    light turns off. This is normally no longer than 30 seconds.

      

THE VEHICLE MAY NOW BE SAFELY REMOTE STARTED. 

                              (See page 6 for Remote Starter Functions.)

If Reservation Mode is not set, the remote starter will not activate. When the 
button is pressed the park lights will flash 4 times. 4 flashes is the diagnostic 
code for “Not in Reservation Mode”

NOTE

Reservation Mode will reset if the doors of the vehicle are opened. To re-enter       

            the vehicle without canceling the Reservation Mode (ex: forgot something..)         
            The vehicle must first be remote started. While the vehicle is running by the 
            remote starter the door may be opened. When done in the vehicle, close the
            door and remotely stop the vehicle by pressing and holding the     button.

Reservation Mode

Summary of Contents for 2500M SERIES





























Reviews: