background image

15

Ultra-Aire SD12 Installer’s & Owner’s Manual

5.  Optional Dehumidifier & Ventilation  

System Controller

When used with Ultra-Aire Whole House Ventilating 
Dehumidifiers, the DEH 3000/3000R allows homeowners the 
ability to monitor and control relative humidity levels in their 
home.

DEH3000 P/N: 

 4028539

DEH3000R (remote) P/N: 

 

4028407

Model: 

 

 DEH  3000 
DEH 3000R (remote)

Operating Voltage: 

 

24 VAC

Max Current  
DMP, COMP, FAN:

 

1 AMP each

Humidity Range/Accuracy: 

 

10 – 95% RH, 

±

 5%

Humidity Setpoint 

35% min – 70% max

Auxillary Relay Capacity:

 

5 Amps, 24VAC

Temp Range/Accuracy: 

 30°-90°F, 

± 

2°F

Size: 

 

4.95"L x 1.06"W x 4.19"H

Major Operations 

n

 Digital control of Relative Humidity (Digital Set-Point) 

n

 Fan/Filter Operation 

n

 Programmable Ventilation Timer

n

 Large, easy-to-read backlit LCD display 

n

 Easy interaction with air handler fan (Interlock/Lockout) 

n

 High Temperature Cut-Out 

n

 Dryout Cycle Timer 

n

 Auto Reboot

n

 Remote Sensor (DEH 3000R Only)

To order call Therma-Stor  
at 1-800-533-7533 or  
Contact your local distributor  
or HVAC contractor.

 

DEH 3000, DEH 3000R DEHUMIDIFIER & VENTILATION SYSTEM CONTROLLER

DEH

 

3000/DEH

 

3000R

DEH

 

3000/DEH

 

3000R

Part No. 4028539

Part No. 4028407

Summary of Contents for 4033170

























Reviews: