Ultra-Aire 4033170 Installer'S & Owner'S Manual Download Page 22

Page: 22 / 24

Ultra-Aire SD12 Installer’s & Owner’s Manual

OPTIONAL PARTS LIST

PART NO.

QTY.

DESCRIPTION

4028539

DEH 3000 Control

4028407

DEH 3000R (with remote)

4021475

MERV 11 Filter (16”x20”x2”)

4027420

MERV 11 Filters 4-Pack

4027424

MERV 11 Filters 12-Pack

4028614

Pump Kit

4025287

MERV 14 Filter Housing

4024370

MERV 14 Filter (20”x24”x4”)

4029087

MERV 14 Filter 3-Pack

Collar Install

Remove the 2 round duct collars, 3 seals and
small bag of mounting hardware from inside the
rectangle opening.

Mount the duct collars to the front of the
dehumidifier using screws provided.

Collars and hardware
are located here.

Door Install

Insert tab on the bottom of the door,
in between the foam installation and
the metal side.

Push down on the plastic door latch
and swing door shut. Once the door is
shut release the door latch.

DOOR AND COLLAR ASSEMBLY

4023672

6” Motorized Damper

4026859

6” Flex Duct 25’

4020128

6” Flex Insulated Duct 25’

4020656

6” Inlet/Exhaust Hood

4024375

10” Gravity Damper

4026969

10” Flex Duct 25’

4022126

10” Flex Insulated Duct 25’

4028399

10” Oval to Round Adapter

Summary of Contents for 4033170

























Search results

Summary of Contents for 4033170

Reviews:

Related manuals for 4033170

Brands by name

Popular brands

Ultra-Aire 4033170, Installer'S & Owner'S Manual

Search results

Summary of Contents for 4033170

Reviews:

Related manuals for 4033170

Brands by name

Popular brands