background image

13

1  TECHNICAL CHARACTERISTICS

We reserve the right to amend this manual without notice.

2  INTRODUCTION

Read this instruction booklet carefully in order to familiarise

yourself with all aspects of the dispenser.

Like all mechanical products, this machine will require cleaning

and maintenance. Good operation can also be affected by any

errors made by the operator during disassembly and cleaning.

For this reason, in the case of daily operations such as

disassembly, cleaning, sanitising and reassembly, it is important

that the person using the dispenser is aware of the procedures

and can perform them without making errors.

3  INSTALLATION

1

Remove the dispenser from the packaging, which you

should keep in case it is needed in the future.

2

Check that the dispenser has not been damaged during

transport. If it has, make a report to the carrier immediately.

3

Position the dispenser on a bench capable of supporting the

weight, even at full load,

 bearing in mind the IMPORTANT

warning in point 1 above. 

4

Allow a minimum clearance of at least 15 cm all around the

dispenser so as not to impede the flow of cooling air.

5

Check the stability of the device, adjusting the height of the

feet if necessary. In the event that the dispenser is provided

with a series of high feet (approximately 100 mm), these must

replace the original ones.

6

Before plugging in the dispenser, check that the mains

voltage is the same as that indicated on the data plate. Connect

the dispenser to a single phase network, using an outlet

complete with earthing as defined by current standards. The

electrical disconnect switch shall have a contact separation in

all poles , providing full disconnection under over voltage

category III conditions. Do not use extension cables to connect
the device to the mains.

7

The dispenser does not leave the factory pre-washed and

sanitised. Before use, it must be disassembled, washed and
sanitised, following the instructions in Chapter 5.3 CLEANING.

4  TO OPERATE SAFELY

1

Do not

 operate the dispenser without reading this

operator’s manual.

2

Do not

 operate the dispenser unless it is properly

grounded.

3

Do not

 use extension cords to connect the dispenser.

4

Do not 

operate the dispenser unless all panels are

restrained with screws.

5

Do not

 obstruct air intake and discharge openings: 15 cm

(6”) minimum air space all around the dispenser.

6

Do not

 put objects or fingers in panels louvers and faucet

outlet.

7

Do not

 remove bowls, augers and panels for cleaning or

routine maintenance unless the dispenser is disconnected from

its power source.

8

This unit can work in a room temperature range between

+5° and +32°C.

9

This unit is 

not

 to be installed in areas subject to water-

spouts..

10

Do not 

use water-jets to clean the unit.

11

The appliance has to be placed in vertical position.

12

Do not

 install the machine in the kitchen.

13

Do not

 store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

14

This appliance is intended to be used in household and

similar applications.

15

The appliance is 

not

 suitable for outdoor use.

16

Do not

 squeeze the main cable.

Transparent removable bowls

n

1

2

3

Capacity of each bowl, approx.

l

6

6

6

Dimensions:

 width

cm

20

40

60

depth

cm

48

48

48

height

cm

62

62

62

Net weight, approx.

kg

25

45

61

Gross weight, approx.

kg

27

48

64

Hermetic compressor

Air-cooled condenser

Overload protector

Noise level lower than 70 dB (A)

IMPORTANT

Electrical characteristics: read the data on the plate of

each individual dispenser. This is located at the bottom

of the front panel, behind the drip tray on the right. The

serial numbers of the devices (preceded by the symbol #)

are shown on the frame below. Always refer to the data

shown on the plate.

IMPORTANT

When transporting or lifting the dispenser, never pick it

up by the transparent containers or the evaporator cylin-

ders. The manufacturer is not liable for damage caused

by such mishandling.

ATTENTION

Make sure the device is properly earthed, otherwise you

may cause electric shocks to persons or damage to the

dispenser.

IMPORTANT

Place the device in such a way that the power cable is

easily accessible.

IMPORTANT

This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way

and understand the hazards involved. Children shall not

play with the appliance. Cleaning and user maintenance

shall not be made by children without supervision.

MINIGEL 1

MINIGE

L 2

MIN

IGEL 3

Summary of Contents for MiniGEL 1 PLUS





















































Reviews: