19
18
Unplug the product immediately from the mains in the event of any breakdown and contact
an authorised Technical support service.
In order to prevent any risk of danger, do not open the control or connection. Only qualified
technical personnel from the brand´s Official Technical support service may carry out
repairs or procedu res on the device.
Any incorrect use or improper handling of the product shall render the warranty null and
void. Only an authorised technical support service centre may carry out repairs on this
product.
B&B TRENDS SL.
disclaims all liability for damages that may occur to people, animals or
objects, for the non-observance of these warnings.
INSTRUCTIONS FOR USE
Completely stretch out the electric blanket over the mattress, leaving a space free at the
top, to place the pillow, fitting the elastic straps of the electric blanket to the mattress,
and then place it under the sheet. Prevent any wrinkles, folds or creases and ensure that
the outlet is at the top of the bed. (See figure 1).
Then proceed to make the bed in the usual way.
Avoid placing any bags or other heavy objects on the bed while the electric blanket is
turned on, as well as its use at the same time as other sources of heat such as hot water
bottles, heating pads or similar products.
In order to prolong the shelf life of your product, make sure that the regulator control
switch is in the “0“ position before connecting or disconnecting it from the mains.
In order to turn on the product, you must select the slider switch on the control, setting it
to position 1, 2 or 3 (Fig.2).
The maximum operation time is 3 hours, after which the automatic safety shut-down will
immediately activate. The product will no longer heat up when in this state.
To turn on the product again, set it to position “0” and select the desired temperature.
Select the “0” position in order to turn off the product before you disconnect the device
from the mains.
This electric blanket comes with a feet zone with a higher temperature to provide
additional comfort and a rapid heating technology, which enables the heat to be felt just 5
minutes after turning on the control knob, regardless of the selected temperature. Set the
temperature to a lower level after this time.
The control should be set to its minimum temperature (level 1) when using the product for
extended periods of time. Try to avoid excessive exposure to heat from high temperatures.
The highest control temperature level (level 3) should be used only for the time necessary
to obtain a comfortable temperature, and the temperature should be gradually lowered
to a lower position after this threshold has been reached.
TROUBLESHOOTING GUIDE
Possible operational problems
PROBLEM
RECOMMENDATION
After turning on the electric blanket, it does not
warm up or only heats up a little.
Make sure that the regulator is properly
connected to the product.
If the electric blanket is not heating up, cover it
with a bed cover, or duvet, placing the regulator
in the maximum position and wait for 30
minutes. If it continues
to not heat up after this time, contact an
authorized service technician.
Checks carried out with the electric blanket
partially uncovered or in the open air are not
reliable, as these may result in erroneous
perceptions of the heat.
After a certain operation time, the product
temperature seems to reduce.
The product has an auto-stop system that
activates after 3 hours of continuous operation.
After this time, the light on the regulator starts
to flash.
If you want to continue to use it, change the
temperature level to level 0, wait a few seconds,
and then select the desired temperature.
The regulator control does not turn on when the
switch is activated.
Ensure that the regulator is properly connected
to the product and that there is voltage in the
socket
of the mains used ,and that the product is
properly plugged in to the same.
PRODUCT DISPOSAL AND CONSERVATION
PRODUCT CONSERVATION
Unplug the product when you do not intend to use
it for an extended period of time to prolong its
shelf-life. Prior to storing the product, allow it to
cool before folding, keep it in its original packaging
in a dry location with the fewest possible folds,
without placing any objects on top.
