VACUUM CLEANING WITH THE USE OF
THE WATER FILTER MODULE
1
Press the “PRESS” button and remove the tank lid.
2
Insert the partition to the grooves in the container
so that the shutters are directed downwards. Make sure
the partition is correctly mounted in the container i.e. the
partition fins should cover the protrusion in the container.
3
Fill the container with 1,2 liter of water. The water
level should be in the range marked on the tank wall.
Do not operate the appliance with an
empty container while vacuum cleaning
with the use of the water filter module.
4
Insert the filtration unit to the tank, make sure
that the two air stub pipes are in the openings of the
vacuum cleaner body.
●
Prepare the vacuum cleaner for operation
according to section
B
.
Do not operate the appliance for too
long without replacing the water in the
container. In case of long-term or very
intensive vacuuming of large amounts of dirt,
the water in the tank which constitutes the first
filtration level may in whole or in a considerable
part be absorbed by the dirt. In such a case,
exchange the water and continue vacuuming.
Avoid vacuuming surfaces covered with substances
which may favor an excessive foaming of the water
inside the tank. If you notice that the water is heavily
foamed, add a foam neutralizer recommended by the
manufacturer of the appliance e.g. “G 478 Buz® Defoam”
in the amount indicated on the packaging.
Vacuuming with the amount of water in
the tank which exceeds the marked,
permissible level may cause the water to
spill to the outside of the appliance. If this
situation repeats often, it may lead to a fast
clogging of the outlet EPA filter.
The vacuum cleaner is equipped with
a float which will automatically block
the suction if the foam filter II (8) is heavily
dirty or the liquid exceeds the maximum level.
In such a case switch off the vacuum cleaner by
pressing the on/off button (1), unplug the
appliance, clean the filter and empty the container.
E
PICKING UP WATER
If you want to use the vacuum cleaner to vacuum liquid,
the vacuum cleaner should be prepared as in the case
of vacuum cleaning with the use of the water filter
module except that:
●
The container should be empty (without water).
●
You should use the nozzle for picking up water
(19)
.
Do not operate the vacuum cleaner with
a full container! Do not vacuum large
amounts of liquid at a time (e.g. with the
hose immersed into water).
If the water exceeds the maximum level during
vacuuming, the float will automatically block the
suction. The maximum capacity of the container is
about 4,0 l. In such a case proceed in the manner
described above in the part concerning the blocking of
suction caused by a dirty foam filter.
End of operation cleaning and
maintenance
●
Switch off the vacuum cleaner by pressing the on/off
button
(1)
and unplug the appliance.
●
Wind the cord by pressing the cord rewind button
(4)
.
While doing this hold the cord to make sure it is not
tangled and the plug does not hit the vacuum cleaner
housing.
●
Press the interlock on the hose end and remove the
hose from the opening.
●
Disconnect the telescopic tube from the hose and
the nozzle or brush.
●
In case of vacuuming or picking up water with the use
of the water filter module, remove the dirty water from
the tank.
●
It is recommended to wash the container, filters
(disassembly below) and partition thoroughly after
each use – changing water several times.
If you do not clean the above-mentioned
parts or clean them insufficiently it may
lead to the loss of the filtration
capabilities of the inserts and foam and cause
the formation of bacteria and mites.
Dry all the cleaned parts thoroughly
before reassembly.
Summary of Contents for AP8000
Page 33: ...4 B EPA 8 1 19 4 0 1 4 1 2 1 2 F G...
Page 36: ...ufesa ufesa 16 230 AR...
Page 37: ...Notes...
Page 38: ...Notes...