UE Systems ULTRAPROBE 10,000SD Instructions Manual Download

Page: 11 / 12

10,000SD

VALVE INSPECTION

Ultraprobe 10,000SD

Valve Inspection:

How To Guide

NOTE:

UE DMS Software available for download at

www.uesystems.com

SAFETY: WRIST STRAP WORN ALL TIMES

INSPECTION PROCEDURE

When

Optimizing

the Sensitivity for

Each

Data

Point,

Arrow Indicators

Guide Which Direction to

Spin

the Dial. A

RIGHT Arrow

Indicates the

Sensitivity is

Too Low

, the Dial Must Be Turned to

the Right to Obtain a Decibel. A

LEFT Arrow

Indicates the Sensitivity is

Too High

When the

Sensitivity

is Optimized, a

Decibel

(dB)

Will Populate On the Display, Ready to Be

Applied to That

Test Point

. The Ultraprobe

10,000SD Display Indicates

Which Test Point

Value is

Being Acquired

. Simply Press

ENTER

to Store That Value. Once All Four (4) Data
Point Values are Stored,

Condition Assessment

Can Be Initiated.

Summary of Contents for ULTRAPROBE 10,000SD













Search results

Summary of Contents for ULTRAPROBE 10,000SD

Reviews:

Related manuals for ULTRAPROBE 10,000SD

Brands by name

Popular brands

UE Systems ULTRAPROBE 10,000SD, Instructions Manual

Search results

Summary of Contents for ULTRAPROBE 10,000SD

Reviews:

Related manuals for ULTRAPROBE 10,000SD

Brands by name

Popular brands