Ublox MAX-M10 Page 65 Integration Manual Download | Manualshive

Page: 65 / 92

background image

MAX-M10M - Integration manual

If the hardware backup mode is not used, leave the V_BCKP pin open.

4.1.4 Supply design examples

The two voltage ranges for V_IO allow several combinations when designing the receiver power
supply. Depending on the chosen combination, there are certain requirements to be considered.
These are summarized in

Option

Nominal supply (V)

Design case / Requirements

V_IO

VCC

1

3.3

3.3

3.3 V design where VCC and V_IO are connected together. See

for designs

using the hardware backup mode, and

for designs without backup supply.

•

VIO_SEL pin left open.

•

Voltage at VCC_RF pin = VCC - 0.1 V.

2

1.8

1.8

1.8 V design with VCC and V_IO connected together. This design requires an
accurate supply. See

for designs using the hardware backup mode, and

for designs without backup supply.

•

VIO_SEL is grounded.

•

Note that the voltage output at VCC_RF = VCC - 0.1 V.

•

Note that the maximum supply tolerance is 1.8 V ± 2 %.

To enter hardware backup mode, set the receiver to software standby mode
with the UBX-RXM-PMREQ message before switching oﬀ V_IO and VCC.

3

1.8

1.8 / 3.3 / 5.0

VCC and V_IO are supplied independently. V_IO is supplied with an accurate 1.8 V
supply. VCC can be either supplied with 1.8 V , 3.3 V or 5.0 V. See

for

designs using the hardware backup mode, and

for designs without backup

supply.
•

VIO_SEL pin is grounded.

•

Note that the maximum supply tolerance is 1.8 V ± 2 %.

•

Voltage at VCC_RF pin = VCC - 0.1 V.

To enter hardware backup mode, switch oﬀ V_IO 100 ms before VCC.
Alternatively, the receiver can be set to software standby mode with the UBX-
RXM-PMREQ message before switching oﬀ V_IO and VCC.

Table 30: Voltage supply options

Figure 21: VCC and V_IO connected to the main supply, and external power supply at V_BCKP

Figure 22: VCC and V_IO connected to the main supply. No external power supply at V_BCKP.

UBX-22038241 - R02

4 Hardware integration

Page 65 of 92

C1-Public

«
...
63
64
65
66
67
...
»

Summary of Contents for MAX-M10





























































































Reviews:

No comments

Related manuals for MAX-M10

Brand: Radio Shack Pages: 52

Brand: Febco Pages: 4

Brand: Cisco Pages: 48

Brand: Lawler Pages: 4

Brand: Waterway Pages: 16

ESD-5550 Series

Brand: GAC Pages: 12

Brand: Gascat Pages: 32

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: VAT Pages: 26

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 140

Brand: µ-Dimension Pages: 48

Brand: µ-Dimension Pages: 2

Brand: Warner Electric Pages: 4

Brand: Trane Technologies Pages: 8

Brand: LAB-EL Pages: 25

Brand: Cardigo Pages: 12

Brand: Sunlover Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands