Ublox MAX-M10 Page 82 Integration Manual Download

Page: 82 / 92

MAX-M10M - Integration manual

supervisor support in MAX-M10M. Therefore in MAX-M10M, the active antenna supply and the
antenna supervisor circuitry (if used) needs to be connected externally as shown in

Figure 39

Figure 35: MAX-M8 vs. MAX-M10M comparison (pin 13 - 15)

Refer to MAX-M8 and MAX-M10M data sheets for details on performance comparison [

A.2 Software changes

Table 34

presents a summary of the key

software-related changes

between u-blox M10 and u-blox

M8.

Feature

Change

Action needed / Remarks

Signals

Default GNSS
conﬁguration

MAX-M10M: GPS, Galileo, QZSS and SBAS.
MAX-M8Q/C/W: GPS, GLONASS, QZSS and SBAS.

Code change (optional)

BeiDou B1C

New signal. BeiDou satellite IDs up to 63 supported. Cannot
be used simultaneously with BeiDou B1I. AssistNow and power
save mode not supported.

Code change (optional)

UBX-22038241 - R02

Appendix

Page 82 of 92

C1-Public

Summary of Contents for MAX-M10





























































































Search results

Summary of Contents for MAX-M10

Reviews:

Related manuals for MAX-M10

Brands by name

Popular brands

Ublox MAX-M10, Integration Manual

Search results

Summary of Contents for MAX-M10

Reviews:

Related manuals for MAX-M10

Brands by name

Popular brands