Ublox MAX-M10 Page 22 Integration Manual Download | Manualshive

Page: 22 / 92

background image

MAX-M10M - Integration manual

Message type

Message content

0

Test mode

47

Monitoring station information

48

PRN mask

49

Data issue number

50

DGPS correction

51

Satellite health

Table 12: Supported QZSS L1S SLAS messages for navigation enhancement

Use the conﬁguration key CFG-SIGNAL-QZSS_L1S_ENA to enable QZSS L1S signal. For further
QZSS SLAS functionality, use the CFG-QZSS-USE_SLAS* conﬁguration keys.

Parameter

Description

CFG-QZSS-USE_SLAS_DGNSS

Apply QZSS SLAS corrections

CFG-QZSS-USE_SLAS_TESTMODE

Allow the correction provided by QZSS satellites that are in test mode

CFG-QZSS-
USE_SLAS_RAIM_UNCORR

If this conﬁguration is set, the receiver will try to estimate the position by using only
corrected measurements; if all corrected measurements are not available, it will not
use any corrections. If this conﬁguration is not set, the receiver will mix corrected
and uncorrected measurements for the navigation solution.

Table 13: QZSS SLAS conﬁguration parameters

If the RAIM option is set, QZSS is the only GNSS time system that measurements can observe.

3.2 Communication interfaces and PIOs

MAX-M10M supports communication over UART and I2C interfaces for communication with a host
CPU. Each protocol can be enabled on several interfaces at the same time with individual settings for,
for example, baud rate, message rates, and so on. In MAX-M10M, several protocols can be enabled
on a single interface at the same time.

3.2.1 UART

MAX-M10M supports a Universal Asynchronous Receiver/Transmitter (UART) port consisting of an
RX and a TX line. The UART can be used as a host interface which supports a conﬁgurable baud rate
and protocol selection.

Neither handshaking signals nor hardware ﬂow control signals are supported.

The UART baud rate can be conﬁgured for selected speeds. Diﬀerent rates than these speeds are
not supported for transmission and reception.

The UART RX interface will be disabled when more than 100 frame errors are detected during
a one-second period. This can happen if the wrong baud rate is used or the UART RX pin is
grounded. An error message appears when the UART RX interface is re-enabled at the end of
the one-second period.

Baud rate

Data bits

Parity

Stop bits

4800

8

none

1

9600

8

none

1

19200

8

none

1

38400

8

none

1

57600

8

none

1

115200

8

none

1

UBX-22038241 - R02

3 Receiver functionality

Page 22 of 92

C1-Public

«
...
20
21
22
23
24
...
»

Summary of Contents for MAX-M10





























































































Reviews:

No comments

Related manuals for MAX-M10

Brand: ABB Pages: 2

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: CAME Pages: 32

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Daikin Pages: 2

Brand: Daikin Pages: 12

Brand: Daikin Pages: 12

Brand: Daikin Pages: 46

Brand: Daikin Pages: 21

Brand: Daikin Pages: 20

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: Xilinx Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands