background image

Lietuviškai 

[Lithuanian]

UBIQUITI NETWORKS deklaruoja, kad  šis UBIQUITI NETWORKS 

įrenginys atitinka esminius reikalavimus ir kitas 1999/5/EB 

Direktyvos nuostatas.

Malti 

[Maltese]

Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITI 

NETWORKS device, jikkonforma mal- ti ijiet essenzjali u ma 

provvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Norsk 

[Norwegian]

UBIQUITI NETWORKS erklærer herved at utstyret UBIQUITI 

NETWORKS device, er i samsvar med de grunnleggende krav og 

øvrige relevante krav i direktiv 1999/5/EF.

Slovensky 

[Slovak]

UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKS 

device, sp a základné po iadavky a v etky príslu né ustanovenia 

Smernice 1999/5/ES.

Svenska 

[Swedish]

Härmed intygar UBIQUITI NETWORKS att denna UBIQUITI 

NETWORKS device, står I överensstämmelse med de väsentliga 

egenskapskrav och övriga relevanta bestämmelser som framgår av 

direktiv 1999/5/EG.

Español 

[Spanish]

Por medio de la presente UBIQUITI NETWORKS declara que el 

UBIQUITI NETWORKS device, cumple con los requisitos esenciales 

y cualesquiera otras disposiciones aplicables o exigibles de la 

Directiva 1999/5/CE.

Polski  

[Polish]

Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt serii 

UBIQUITI NETWORKS device, spełnia zasadnicze wymagania i inne 

istotne postanowienia Dyrektywy 1999/5/EC.

Português 

[Portuguese]

UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device, 

está conforme com os requisitos essenciais e outras disposições da 

Directiva 1999/5/CE.

Română 

[Romanian]

Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitiv 

UBIQUITI NETWORKS este în conformitate cu cerințele esențiale și 

alte prevederi relevante ale Directivei 1999/5/CE.

Online Resources

Support 

support.ubnt.com

Community 

community.ubnt.com

Downloads 

downloads.ubnt.com

Summary of Contents for RocketDish 5G30

























Reviews: