Ubiquiti RocketDish 5G30 Quick Start Manual Download | Manualshive

Page: 14 / 24

background image

14. Lift the Dish Reflector and align the two lower Hex Head

Bolts with the slots on the Lower Pole Bracket. Seat the bolts
in the slots.

15. Attach each arm of the Upper Pole Bracket to the Mounting

Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer.

«
...
12
13
14
15
16
...
»

Summary of Contents for RocketDish 5G30

























Reviews:

No comments

Related manuals for RocketDish 5G30

Brand: ZCG Pages: 2

Brand: Altelix Pages: 2

Cell-Max CMAX-O-TCPUSEWI53

Brand: CommScope Pages: 2

Brand: Renkforce Pages: 3

airMAX airGrid M5HP

Brand: Ubiquiti Pages: 28

Brand: A.H. Systems Pages: 15

Brand: A.H. Systems Pages: 15

Brand: A.H. Systems Pages: 19

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 14

TADA2420 - ANTENNA SYSTEM

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 56

Brand: Steren Pages: 2

Brand: WADE Antenna, Inc. Pages: 9

Brand: Wireless Beehive Pages: 7

Brand: E-Bench Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands