Assembly
Attention, important!
When in doubt about how to install the device correctly, please contact an
expert or a specialist workshop and let them carry it out !
A suitable measurement instrument is required for the optimum set-up of the
satellite antenna with the inserted LNB for digital TV/radio reception.
Install the LNB to the corresponding bracket (feed horn) of your satellite antenna. The
bracket must have an opening diameter of 40 mm.
The round side of the LNB must point towards the satellite antenna. Furthermore,
make sure that the LNB connectors point down.
An angle indicator is located on the side of the LNB. Depending on your lo-
cation and the satellite to be received, the LNB must be rotated accordingly.
Connection
The outputs of the Quattro LNB must be connected to a suitable multiswitch. Always
pay attention to the correct pin assignment of the connectors. The assignment of the
LNB outputs is indicated next to the sockets.
L/V
lower frequency range (low band), vertical polarisation
H/V
upper frequency range (high band), vertical polarisation
L/H
lower frequency range (low band), horizontal polarisation
H/H
upper frequency range (high band), horizontal polarisation
Direct connection to an output of the Quattro LNB to a SAT receiver is not
possible (in this case, only some of the stations would be available).
The multiswitch you use must support a Quattro LNB.
When connecting the LNB to the multiswitch, use a suitable antenna cable and
F-plugs.
A high-quality, double-shielded antenna cable that is suitable for satellite
signals must always be used so that the LNB signals can be transferred.
If the cable between the LNB and the multiswitch is very long, make sure
that the cable has a low attenuation.
The F-plugs used for connection to the LNB must be suitable for operation
outdoors so that moisture cannot get in.
Slide the plastic weather protection cover of the LNB over the four F-plugs. This will
protect them from precipitation.
Disposal
The product must not be disposed of in the household waste.
Please dispose of the product at the end of its service life according to the
current statutory requirements.
Technical data
Power supply ........................... via multiswitch
Operating voltage.................... 13 - 19 V/DC
Power consumption................ max. 200 mA
Frequency range (input) ......... Low band: 10.7 - 11.7 GHz
....................................................
High band: 11.7 - 12.75 GHz
Frequency range (output) ....... Output “L/V”: 950 - 1950 MHz, vertical position
....................................................
Output “H/V”: 1100 - 2150 MHz, vertical position
....................................................
Output “L/H”: 950 - 1950 MHz, horizontal position
....................................................
Output “H/H”: 1100 - 2150 MHz, horizontal position
L.O frequency........................... Low band: 9.75 GHz
....................................................
High band: 10.6 GHz
Type ........................................... Quattro LNB
Impedance ............................... 75
Ω
Amplification ............................ 55 dB (typical)
Noise factor ............................. 0.4 dB (typical)
Feed horn.................................. Ø 40 mm
Dimensions (L x W x H) .......... 120 x 68 x 81 mm
Weight ....................................... approx. 226 g
G
Operating instructions
Quattro LNB
Item no. 1362485
Intended use
The product is intended for installation in a LNB bracket (Ø 40 mm) of a satellite an-
tenna and is used there to receive suitable digital satellite signals (TV, radio).
The product is especially intended for connection to a suitable multiswitch; direct con-
nection to a SAT receiver is not possible.
Always observe the safety instructions and all other information included in these op-
erating instructions.
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package contents
• LNB
• Operating instructions
Explanation of symbols
This symbol points to specific risks associated with handling, function or
operation.
The “arrow” symbol points to special tips and operating information.
Safety instructions
Damage due to not following these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. In such
cases, the warranty will be null and void.
• The unauthorised conversion and/or modification of the product is not
permitted for safety and approval reasons (CE). Do not disassemble the
product.
• The product is not a toy and should be kept out of the reach of children.
• The product is designed for operation outdoors. However, pay attention
to the correct operating position during installation (the connectors must
point down).
• Observe the safety instructions and installation information of your satel-
lite antenna. The same applies for the connection of cables/devices to the
LNB outputs.
• Follow all applicable accident prevention regulations during installation
and connection, e.g. when using a ladder to install the LNB at a satellite
antenna. Only use suitable tools for installation and connection.
In case of doubt, get the installation and connection done by a specialist!
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
