background image

Specifications

RocketDish RD-5G30-LW

Dimensions

650 x 650 x386 mm (25.6 x 25.6 x 15.2")

Weight

7.4 kg (16.31 lb)

(Mount Included)

Frequency

5.1 - 5.9 GHz

Gain

30 dBi

Max. VSWR

1.6:1

Wind Survivability

200 km/h (125 mph)

Wind Loading

790 N @ 200 km/h (178 lbf @ 125 mph)

Polarization

Dual Linear

F/B Ratio

30 dB

ETSI Specification

EN 302 326 DN2

Mounting

Universal Pole Mount, Rocket Bracket, and 

Weatherproof RF Jumpers Included

Safety Notices

1.  Read, follow, and keep these instructions.
2.  Heed all warnings.
3.  Only use attachments/accessories specified by the manufacturer.

WARNING:

 Do not use this product in location that can 

be submerged by water. 

WARNING:

 Avoid using this product during an electrical 

storm. There may be a remote risk of electric shock from 
lightning. 

Electrical Safety Information

1.  Compliance is required with respect to voltage, frequency, and current 

requirements indicated on the manufacturer’s label. Connection to a 
different power source than those specified may result in improper 
operation, damage to the equipment or pose a fire hazard if the 
limitations are not followed.

2.  There are no operator serviceable parts inside this equipment. Service 

should be provided only by a qualified service technician.

Summary of Contents for RocketDish 5G30

























Reviews: