Ubiquiti RocketDish 5G30 Quick Start Manual Download Page 7 | Manualshive

Page: 7 / 24

background image

4. Attach the Rocket to the Mounting Bracket.

a. Align the mounting tabs on the back of the Rocket with

the Rocket mount.

b. Slide the Rocket down to lock it into place.

5. Attach the other end of the RF Cables to the RF connectors

on the Rocket in this combination: H to Chain 1 and V to
Chain 0. Then slide the jackets over the RF connectors to
protect them.

«
...
5
6
7
8
9
...
»

Summary of Contents for RocketDish 5G30

























Reviews:

No comments

Related manuals for RocketDish 5G30

Brand: Datron Pages: 16

Brand: American Communication Systems Pages: 5

Brand: Hirschmann Pages: 2

Brand: L3 Pages: 122

LiteBeam LBE-5AC-23

Brand: Ubiquiti Pages: 28

Brand: TERK Technologies Pages: 16

Brand: Hughes Network Systems Pages: 27

9711-44 KU-BAND TX/RX

Brand: Sea Tel Pages: 256

Brand: Etec Pages: 8

Brand: SLX Pages: 2

digiTop 27800RG

Brand: SLX Pages: 2

Brand: BandLuxe Pages: 14

Brand: Shively Labs Pages: 28

Brand: King Controls Pages: 32

Brand: Jaybeam Wireless Pages: 6

Brand: Metronic Pages: 2

Brand: Abel & Profit Pages: 3

Brand: EAntenna Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands