uAvionix tailBeaconX STC Installation Manual Download | Manualshive

Page: 13 / 28

background image

UAV-1003599-001

13

Rev A

7 Installation

7.1 Unpacking and Inspecting

Carefully unpack the device and make a visual inspection of the unit for
evidence of any damage incurred during shipment. If the unit is damaged,
notify the shipping company to file a claim for the damage. To justify your
claim, save the original shipping container and all packing materials.

7.2 Authorized Part Numbers

tailBeaconX

Item

P/N

tailBeaconX Hardware

UAV-1003648-001

tailBeaconX Software

UAV-1002393-004

tailBeaconX TSO Installation Kits

Item

P/N

tailBeaconX Universal Installation Kit

UAV-1003793-001

«
...
11
12
13
14
15
...
»

Summary of Contents for tailBeaconX STC





























Reviews:

No comments

Related manuals for tailBeaconX STC

SkyRanger Nynja 600

Brand: Flylight Airsports Pages: 62

Brand: Nova Pages: 41

Brand: ITV Pages: 60

Brand: MAC PARA Pages: 32

Brand: MAC PARA Pages: 18

ALUULA G Series

Brand: Ocean Rodeo Pages: 4

BEECH BARON 58P

Brand: Raytheon Pages: 654

Alpine Peak 2 L

Brand: U-Turn Pages: 25

Brand: U-Turn Pages: 32

Brand: U-Turn Pages: 35

Brand: U-Turn Pages: 38

Brand: U-Turn Pages: 55

Alpine Peak 2 XS

Brand: U-Turn Pages: 25

HC-C2YR-4CF/FC8475-6

Brand: Hartzell Pages: 306

Brand: AIR TRACTOR Pages: 159

Brand: Roko Aero Pages: 69

Brand: Gradient Pages: 15

Brand: Gradient Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands