UAS SMOGHOG SHM-05C, Owner'S Manual

Page: 13 / 32

reV: 17f
SMoGHoG
®
SHM Series Models
9
3.5 ELECTRICAL CONNECTION
the SHM is available with various controls configurations.
refer to the section headings below and follow the
section instructions that best align with your specific unit.
the SHM customer electrical connections are located
on the left side of the unit in most instances as shown in
figure 1B/d. the supply voltage and fLa will be noted
on the nameplate. the blower and system controls are
factory pre-wired for operation. the touchscreen controls
require field wiring and connections for the remote display
enclosure. Wiring diagrams for the various SHM controls,
blower arrangement and supply voltage options are
available within the appendix of this manual. Note that the
SHM does not contain the main disconnect or fuses for
the supply power.
electrical installation should be completed by a qualified
professional and done in accordance with all applicable
codes and regulations.
Power cord and connection into unit will be supplied by
the customer.
unit is available in the voltages shown below:
TABLE 1
SHM Voltage and Full Load Amps
Note: When making the main power connections to the
unit, fan rotation check is not required on advanced units
with ec blowers.
Unit Volt PH Hz RPM FLA
SHM-05C 208 3 50 2660 2.35
SHM-05C 230 3 50 2710 2.35
SHM-05C 240 3 50 2730 2.45
SHM-05C 400 3 50 2710 1.35
SHM-05C 208 3 60 3980 2.7
SHM-05C 230 3 60 3040 2.7
SHM-05C 240 3 50 3070 2.75
SHM-05C 460 3 60 3150 1.6
SHM-08C 208 3 50 2620 2.9
SHM-08C 230 3 50 2645 2.95
SHM-08C 240 3 50 2675 3.05
SHM-08C 400 3 50 2645 1.7
SHM-08C 208 3 60 2840 3.9
SHM-08C 230 3 60 2920 3.75
SHM-08C 240 3 60 2970 3.75
SHM-08C 460 3 60 3065 2.1
SHM-08C-A 208 3 50/60 2600 3.6
SHM-08C-A 230 3 50/60 2600 4.6
SHM-08C-A 380 3 50/60 2600 2.3
SHM-08C-A 460 3 50/60 2600 2.8
TABLE 2
Wiring Diagrams
3.5.1 ELECTRICAL SUPPLY POWER
the main power supply is connected to the SHM unit
through a customer sourced, sealed, 1/2˝ conduit connector
that can be installed into the 7/8˝ hole next to the electrical
box. After feeding wires through the coupling, or cord grip
if desired (neither are provided), terminations are made
on the main bus bar terminal for each phase and frame
ground connection on the advanced units, or on the
terminal block in the basic units. the electrical panel also
contains the unit circuit breakers and dc power supply for
the controls components on the advanced units. utilize
table 1 for wire, fuse and disconnect sizing for your
respective product model.
a second conduit location directly below the first is also
located on the side of the advanced unit for low voltage
connections for the remote panel and for the Machine
interlock feature. ensure that the rear electrical panel
cover is in place and secured prior to operating the unit.
refer to the electrical wiring diagrams listed in table 2 for
additional wiring information.
3.5.2 ELECTRICAL BASIC CONTROLS
the basic electrical controls consist of only a prewired
motor and terminal block connection point. the customer
is expected to source a disconnect or manual motor
starter or add it as an option on the order. the terminal
block in the electrical box on the left side of the unit is
factory prewired to the blower motor. When installing this
unit in the field the customer will connect their factory
power to the opposite side of the terminal block and the
frame ground.
Descrip�on of Wiring Diagram
Appendix
Basic Units A1
Remote Panel Touch Controls A2
Advanced Unit W/ Remote Controls A3
Transformer 575:480 A4
CAUTION