SAFETY INSTRUCTIONS
5
4.22
CHECK DAMAGED PARTS.
Verify all machine guards are in good condition and will function properly
before using the machine. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions that
may affect machine operation. A guard, power switch or other part that is
damaged should be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this instruction manual. Do not oper-
ate machine if lever or engine on/off switch does not function properly.
4.23
SECURELY MOUNT ACCESSORIES TO THE MACHINE.
Extra care must be taken an elevated location to prevent injury to some-
one on a lower level in the event the tool or accessory should drop. Do
not operate without fall protection for operator and debris protection for
public.
4.24
NEVER TOUCH THE MOVING PARTS.
Never touch moving parts such as shaft and drill extensions.
4.25
STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS
DETECTED.
Stop using machine immediately if any abnormalities are observed during
operation. Examples of abnormalities include unusual noise and vibration.
4.26
WHEN REPLACING A PART, USE THE SAME TYPE
AND QUALITY.
When replacing a component part with a new one, use only the same
type and quality of new part. Never attempt to repair a machine if you are
unfamiliar with proper procedures and techniques required.
4.27
LOAD AND UNLOAD SAFELY.
Use proper heavy lifting procedures. Read & understand manuals before
loading & unloading.
4.28
SAVE THESE INSTRUCTIONS.
Refer to this operations and maintenance manual as well as any addition-
al instructions included from other manufacturers and organizations.
4.29
REFER TO METABO MANUAL
Refer to Metabo 18v 5.2ah Li-ion Battery Pack Owner’s Manual included
with your VEX kit for operations,maintenance and safety gudelines.
DUST WARNING
Cutting, especially when DRY cutting, generates dust that comes
from the material being cut, which frequently contains silica.
Silica is a basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to excessive amount of
such dust can cause:
• Respiratory diseases (affecting your ability to breath), including
chronic bronchitis, silicosis and pulmonary fibrosis from exposure
to silica. These diseases may be fatal;
• Skin irritation and rash; and
• Cancer according to NTP* and IARC*
* National Toxicology Program, International Agency for Research
on Cancer
Take precautionary steps
• Avoid inhalation of and skin contact with dust, mist and fumes;
• Wet cut when feasible, to minimize dust;
• Wear and ensure that all bystanders wear appropriate respiratory
protection such as dust masks designed to filter out microscopic
particles. (See OSHA 29 CFR Part 1910.1200)
California Prop 65 Warning: Use of this product can cause exposure to
materials known to the State of California to cause cancer and/or birth
defects or other reproductive harm.
Waterworks
Division
P: 866 987-7297 F: 813-621-7125
Visit us at www.ussaws.com
ONLY OPERATE VEX400 WITH DRILL
IN SPEED POSITION 1
This tool creates an enormous amount of force.
Beware of crushing your fingers or other body parts.
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
UNDERSTANDING OF THE OWNERS MANUAL
WHEN OPERATING THIS MACHINE
ALWAYS WEAR SAFETY APPROVED
HEARING PROTECTION
EYE OR FACE PROTECTION
PROTECTIVE HELMET
PROTECTIVE GLASSES OR FULL FACE PROTECTION
WEAR HAND PROTECTION
WARNING: Improperly maintaining the JS including the Honda engine or failing to correct a problem before
operation could cause a malfunction resulting in a serious injury. Always perform a pre-operation inspection before
each operation and correct any problem. See Honda Engines Owner's Manual.
5.2
Check the condition of the Honda engine. See the section titled "Before operation - is your
engine ready to go?" in the Honda Engines Owner's Manual.
WARNING: Exhaust gas from gasoline engines contains dangerous carbon monoxide. Breathing it can cause
unconsciousness and even kill you. Always operate gasoline engine machines in a well-ventilated area. Do not
operate in areas where exhaust fumes could accumulate without wearing appropriate respiratory protection.
Consult your employer and OSHA regarding use of appropriate respirator for dangerous carbon monoxide
gases. See Figure 7.
EEnnggiinnee eexxhhaauusstt ccoonnttaaiinnss
ppooiissoonnoouuss ccaarrbboonn
m
moonnooxxiiddee ggaass.. Breathing
it could cause death.
Operate machine in well
ventilated area.
FFiigguurree 77 -- W
Waarrnniinngg llaabbeell -- eennggiinnee eexxhhaauusstt ccoonnttaaiinnss ccaarrbboonn m
moonnooxxiiddee ggaass
1111
