PowerSeries Pro Installation Guide
Earth ground wiring
Using the supplied insulated green wire, connect the earth ground terminal
on the HS65WPSx power adapter to the earth ground screw and nut
assembly as shown in the diagram.
The earth ground screw and nut assembly must be mounted to the cabinet
to one of the designated holes marked with the earth ground symbol
.
Figure 1-13 Earth ground installation
1
3
4
5
2
6
Item
Description
1
Nut
2
Earth ground connection from building electrical installation.
Note:
This ground connection goes to HS65WPSNA power
adapter EGND connections when this power adapter is mounted
in the cabinet.
3
Cabinet
4
Star washer
5
Bolt
6
Earth ground symbol
Enrollment
All optional modules and devices must be enrolled on the system. During
enrollment, the electronic serial number (ESN) of each device is identified
to the control panel and zones are assigned. A wireless transceiver
HSM2HOST or an RF keypad must be enrolled first before wireless
devices can be enrolled.
Enrolling modules
During automatic and manual enrollment, if an attempt is made to enroll
more than the maximum number of modules, an error tone sounds and a
message is displayed on LCD keypads.
Modules can be enrolled automatically or manually using section [902] of
Installer programming.
To confirm that a module has been successfully enrolled, use Installer
programming section [903].
Enroll wireless devices
Wireless devices are enrolled via the wireless transceiver module and
Installer Programming section [804][000].
Auto enrollment
To enroll a wireless device using this method, press and hold the Enroll
button on the device for 2-5 seconds until the LED lights then release the
button. The alarm panel automatically recognizes the device and the keypad
displays a confirmation message. The device ID and next available zone
number are displayed. Press [*] to accept or scroll to another available
zone number. Batteries must be installed in the wireless device in order to
enroll.
Pre-enrollment
Pre-enrollment is a two step process. The first step requires entering each
device ID ([804][001]-[716]). Every wireless device has an ID printed on
the sticker attached to the device. The format is XXX-YYYY where:
l
XXX identifies the type or model of the device
l
YYYY is a short encrypted ID used by the system to identify the
specific device
Pre-enrollment can be done at a remote location and using DLS/SA. The
second step is to press the enrollment button on the device, usually done
on location. Installer Programming does not have to be entered at this step.
Both steps must be performed in order to complete the enrollment.
Programming methods
The alarm system can be programmed using the following methods:
Table 1-6 Programming Methods
Method
Description
Procedure
Template
programming
Use pre-defined templates
to quickly apply basic
programming and to set up
DLS downloading.
Press [899] at the “Enter
Section” screen.
See Template Programming
below for details.
DLS
programming
Download and apply
programming using DLS 5
For local DLS, use a micro
USB cable or a Wi-Fi dongle
and laptop with DLS-5
software installed.
For remote DLS, use a
telephone line, cellular
network or the Internet.
Installer
programming
Manually program all alarm
system and device options.
Press [*][8][installer code]
while the system is disarmed.
Viewing programming
Programming sections can be viewed from any system keypad.
Generally, programming options are accessed in the following way:
1.
Enter Installer Programming mode ([*][8]).
2.
Navigate to a specific programming section.
3.
Select an option to view or change its programming.
All programming options are numbered and can be accessed by navigating
through the menu, or by keying in the program section number. For toggle
options, the name of the option is displayed.
Use the keypad numbers to toggle options on or off. Sections requiring
data input, such as phone numbers, display the full data in fields up to 32
characters long. To input data, use the scroll keys to select a character then
press the keypad button corresponding to the number/letter required. Scroll
to the next character and repeat the procedure as needed. Press the [#] key
to save changes and exit the program section.
Minimum Required Programming
Once basic installation of the alarm panel is complete, the following
general configuration options can be set.
Time and Date
Use this section to program the alarm system clock.
Menu: [*][6][Master Code] > Time and Date
Keypad: [*][6][Master Code] + 01
- 8 -
