TYAN S2725 Manual Download Page 5 | Manualshive

Page: 5 / 52

background image

5

http://www.TYAN.com

Integrated IDE (SATA)

•Independent DMA operation on 2 ports
•DMA Transfers up to 1.5Gb/s
•Supports RAID 0 (with ICH5R)

Integrated IDE (Parallel ATA)

• Provides two PCI bus master channels
for up to four Enhanced IDE
• Support for UDMA 33/66/100 IDE drives
and ATAPI compliant devices

NOTE:

only 4 total IDE drives can be used

simultaneously (SATA and PATA combined)
Also, when using combination Parallel ATA and
Serial ATA, only the Primary connector of the
PATA will function.

Integrated I/O

• One floppy connector supports two drives
• Two 9-pin serial ports (one connector and one
header)
• One 25-pin ECP/EPP/SPP parallel port
header
• Four USB 2.0 ports (2 rear connectors and 2
headers) **
• PS/2 mouse and keyboard connectors

BIOS

• AMI BIOS 8.0 on 4Mbit Flash ROM
• LAN remote boot (PXE) and SMBIOS v2.3
support
• BIOS Boot Specification v3.1 (BBS) support
• Auto configuration of IDE hard disk types

Form Factor

• ATX footprint (12” x 9.8”)
• ATX12V/EPS12V power connector
• One serial connector, & one VGA connector
• Stacked USB (two) connectors
• Stacked PS/2 mouse and keyboard
connectors
• Two RJ-45 Side-by-side connectors with
LEDs (GN version has one RJ45)

Integrated 2D/3D Graphics

• ATI RAGE XL PCI graphics controller
• 8MB Frame Buffer of video memory

System Management*

• Total of seven 3-pin fan headers
• Six fan headers with tachometer monitoring
• One 2-pin Chassis Intrusion header
• Temperature, voltage and fan monitoring
• Watchdog timer

Power Management

• ACPI 2.0 compliant

PCI Bus

• PCI rev 2.3 specifications at 33Mhz.

Hyper-Threading Support In:

Windows 2000 Server
Windows 2000 Advanced Server
Windows XP Pro
Windows NT 4.0 Server
Windows Server 2003
Linux (Kernel 2.4.18) or higher

TYAN reserves the right to add support or
discontinue support for any OS with or
without notice.

Regulatory

• FCC Class B (Declaration of Conformity)
• European Community CE (Declaration of
Conformity)

*

See Appendix III (Pg 45) for details In Tyan

SMDC

** Please see page 33 for instructions on
how to enable internal USB ports

«
...
3
4
5
6
7
...
»

Summary of Contents for S2725





















































Reviews:

No comments

Related manuals for S2725

Brand: Yamaha Pages: 96

Brand: SurfLink Pages: 9

A75A-G35 Series

Brand: MSI Pages: 72

Brand: ASROCK Pages: 39

A20-OLINUXINO-LIME

Brand: OLIMEX Pages: 49

Brand: Microchip Technology Pages: 34

Brand: Wolfson Pages: 12

Brand: Texas Instruments Pages: 18

LANPARTY UT 915P-T12

Brand: DFI Pages: 124

Brand: DFI Pages: 85

Brand: A-Trend Pages: 49

EVAL-AD7761FMCZ

Brand: Analog Devices Pages: 17

Brand: Abit Pages: 88

Brand: TOHATSU Pages: 102

Brand: TOHATSU Pages: 76

Brand: Diamond Systems Pages: 45

Brand: AKM Pages: 46

WOLFDALE1333-DVI

Brand: ASROCK Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands