TYAN S2725 Manual Download Page 36

Page: 36 / 52

http://www.TYAN.com

3.16 – ACPI Advanced

Options related to advanced power management settings interface can be altered through the
following options.

ACPI APIC Support

This option allows you to define whether or not to enable ACPI
management features.

BIOS

AML ACPI Stable

Please leave this option at its default setting. This setting toggles
BIOS control of ACPI power features.

Headless Mode

After Power Fail

Enable

Disable

Previous

State

Allows system to reboot after a power failure.

Power button instant off

Enabled

Disabled

Choose between instant on/off or a 4 second delay.

Watchdog Timer

Enable

Disable

Do not enable unless you are familiar with this
feature

WOL S1 & S5

Enabled

Disabled

Enables Wake On Lan support. (Only on 82551
NIC.)

3.17 – Boot

Options related to boot dev ices can be altered through the following.

Boot Device Priority

1st Boot Device
2nd Boot Device
3rd Boot Device

Settings for boot priority. These can be
customized depending on your
preference.

Hard Disk Drives

Specifies the boot sequence for hard drive booting. This option
will show all storage devices.

Removable Devices

Specifies the boot sequence for removable drive booting. This
option will show all removable devices.

ATAPI CDROM Drives

Specifies the boot sequence for CD-ROM drive booting. This
option will show all CD-ROM devices.

Interrupt 19 Capture

This option allows removable devices to act as non-removable
devices. Some SCSI RAID cards will need this one enabled.
Please refer to your SCSI card’s documentation.

3.18 – Security

Options related system security can be altered through the following.

Change Supervisor

Password

Changes system password.

Change User Password

Changes boot password.

Clear User Password

Clears boot password.

Boot Sector Virus

Protection

Enabled

Disabled

Toggles protection of boot sector on the hard drive
from being modified.

3.19 – Exit

Options related exiting and saving can be done using the following.

Exit Saving Changes

Exit and save options.

Exist Discarding Changes

Exit but don’t save options.

Load Setup Defaults

Load the BIOS setup default settings.

Discard Changes

Discard any changes made.

Save Changes

Save changes.

Summary of Contents for S2725





















































Search results

Summary of Contents for S2725

Reviews:

Related manuals for S2725

Brands by name

Popular brands

TYAN S2725, Manual

Search results

Summary of Contents for S2725

Reviews:

Related manuals for S2725

Brands by name

Popular brands