TYAN S2725 Manual Download Page 13

Page: 13 / 52

http://www.TYAN.com

2.7

– Fan Header Information

Fan #

Fan Description

Functions

Amp Rated

(Maximum)

CPU 2 Fan

RPM Read and controlled

1.2A

CPU 1 Fan

RPM Read and controlled

1.2A

Chassis Fan 3

RPM Read and controlled*

1.2A or 2A*

Chassis Fan 4

RPM Read

1.2A

Chassis Fan 5

RPM Read

1.2A

Chassis Fan 6

RPM Read

1.2A

Chassis Fan 7

None

* Fan3 can support a fan up to 2 Amperes current by setting JP3 jumper.

FAN3 Current Rate Select (JP3)

Normal

Up to 2 Amp on FAN3

Jumper open =

FAN3 supports RPM read and fan

control. FAN3 current rate is up to 1.2 Amperes.

Jumper closed

= FAN3 supports RPM read, but no

fan control. FAN3 current rate is up to 2 Amperes.

FAN connectors

Use these headers to connect cooling fans, both chassis and
processor fans, to your motherboard. Cooling fans help keep the
system more stable and operating reliably for its product life.

+12V fans supported

Summary of Contents for S2725





















































Search results

Summary of Contents for S2725

Reviews:

Related manuals for S2725

Brands by name

Popular brands

TYAN S2725, Manual

Search results

Summary of Contents for S2725

Reviews:

Related manuals for S2725

Brands by name

Popular brands