TVS TVS XL 100 Manual Download Page 36 | Manualshive

Page: 36 / 44

background image

REAR SHOCK ABSORBERS

TVS XL 100 is provided with 5 step adjustable rear
shock absorbers to meet different load condition.
There are 5 notches for adjusting spring load. If the
spring is adjusted to the minimum notch, then the
shock absorber will be softer which is good for light
loads.
If the spring is adjusted to maximum notch, then it
will be stiffer which is good for heavy loads.
Adjust the spring preload by shifting the adjuster to
the required notch according to the different load
condition.

Caution

Keep both left and right shock absorbers spring
adjusters in the same position.

The more you compress the shock absorber
spring, the suspension becomes more stiff.

MAINTENANCE

-32-

HARD

SOFT

MAINTENANCE

«
...
34
35
36
37
38
...
»

Summary of Contents for TVS XL 100













































Reviews:

No comments

Related manuals for TVS XL 100

Brand: Yamaha Pages: 572

Brand: Yamaha Pages: 584

Brand: Yamaha Pages: 410

Brand: Yamaha Pages: 576

Brand: Yamaha Pages: 668

Brand: Yamaha Pages: 596

Brand: Yamaha Pages: 656

Brand: Yamaha Pages: 378

RACE 13100CP520

Brand: Yoshimura Pages: 7

Brand: Cobra Pages: 38

Brand: Ice Bear Pages: 64

Brand: X&I Pages: 59

Brand: Aim Pages: 47

Brand: JIMS Pages: 2

Brand: APRILIA Pages: 80

Brand: Ruroc Pages: 36

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands